Meritor MM-0861 Скачать руководство пользователя страница 52

Страница: 52 / 118

MM-0861 / Revised 06-22
Page 50

Printed in USA

5 Disassembly

4000194c

HIGH AND LOW
SHIFT FORK AND
SHAFT ASSEMBLY

DOUBLE-GEAR

IDLER SHAFT

Figure 5.22

9. Remove the single-gear idler shaft on MTC-4213X, or rear

output on MTC-4208X/XP/XL/XLEV/XLEC and MTC-4210X/
XP/XL/XLEV/XLEC, and the double-gear idler shaft from the
case. Figure 5.23.

4000195a

Figure 5.23

10. Remove the front output shaft, clutch collar, shift fork, and

spring as an assembly.

11. Remove the shift cylinder and push rod from the front case.

12. Remove the two locating dowel pins. Note their correct

location.

Disassemble the Front Output Shaft Assembly

1. Temporarily install the yoke and nut. Secure the yoke to

prevent the shaft from rotating when removing the rear nut.
Support the shaft correctly.

2. Remove the rear nut and washer.

3. Remove the yoke.

4. Prepare the shaft for bearing and gear removal. Install the

front output shaft into a press with the rear of the output shaft
facing UP. Support the shaft correctly. Figure 5.24.

PRESS

SHAFT

BLOCK

4007098b

Figure 5.24

5. Press the shaft DOWNWARD to remove the rear tapered roller

bearing, helical gear, clutch collar, and needle bearing from
the assembly.

6. Install a bearing separator or other suitable tool below the

forward roller bearing. Figure 5.25.

PRESS

SHAFT

BEARING

SEPARATOR

BLOCK

4007099b

Figure 5.25

7. Install the output shaft assembly into a press and support it

correctly. Figure 5.25.

8. Press the output shaft DOWNWARD to remove the front roller

bearing.

Disassemble MTC-4213X Rear Output Shaft Assembly

DANGER

Observe all hazard alerts provided by the press manufacturer.
Death or serious personal injury and damage to components can
result.

Содержание MM-0861























































































































Результаты поиска

Содержание MM-0861

Отзывы:

Бренды по названию

Популярные бренды

Meritor MM-0861, Руководство по обслуживанию

Результаты поиска

Содержание MM-0861

Отзывы:

Бренды по названию

Популярные бренды