manualshive.com logo in svg

Meritor MM-0861, Руководство по обслуживанию

Поделиться
Скачать
Meritor MM-0861 Скачать руководство пользователя страница 54

Copyright Meritor, Inc., 2022

MM-0861  /  Revised 06-22
Page 52

Printed in USA

5     Disassembly

4000200a

SNAP RING

SPACER
(XLEV/XLEC MODELS)

Figure 5.30 

MTC-4208XEV/XLEC AND MTC-4210XLEV/XLEC

4011710c

SNAP

RING

OIL

SPACER

NEEDLE BEARING

(XLEV/XLEC ONLY)

LOW-RANGE

HELICAL GEAR

INPUT

SHAFT

Figure 5.31 

6.  MTC-4208X/XP and MTC-4210X/XP Only:

 

Remove the internal pump, if equipped, from the input-bearing 
cage to service the front input shaft tapered roller bearing 
cone and cup.

a. Remove the six bolts retaining the oil pump to the input-

bearing cage.

b. Mark the position of the pump to the cage for reassembly. 

Figure 5.32.

4000201b

OIL INLET

PORTS

Figure 5.32 

c. Inspect the pump inner rotor in the spline area for cracks or 

other damage. The entire pump must be replaced if the pump 
or inner gear rotor is damaged in any way. The bearing cup is 
pressed into the bearing cage.

d. Remove the relief valve and spring.

7.  Replace the bearing cone and cup as necessary.

Idler Gear and Rear Output Shaft Disassembly

1.  Use a suitable bearing cone puller to remove the bearing 

cones as necessary from the single idler-gear shaft, rear 
output shaft on MTC-4208 and MTC-4210 transfer cases, or 
double idler-gear shaft assemblies.

2.  Inspect and replace bearing cones with new as needed. 

Replace bearing cones and cups as a set. If the bearings are 
going to be reused, then keep them together and do not mix 
with other bearings.

3.  Inspect the shafts and gears for wear or damage.

Remove the Bearing Cups

1.  Correctly support the transfer case half.

2.  Use a suitable puller to remove the bearing cups from the 

transfer case half. Figure 5.33.

4007155a

BEARING

CUP PULLER

BEARING

CUP

Figure 5.33 

3.  Clean and save the shims so they can be used to measure the 

shim pack thickness during reassembly, if necessary.

Содержание MM-0861























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды