manualshive.com logo in svg

Meritor MM-0861, Руководство по обслуживанию

Поделиться
Скачать
Meritor MM-0861 Скачать руководство пользователя страница 74

Copyright Meritor, Inc., 2022

MM-0861  /  Revised 06-22
Page 72

Printed in USA

7     Assembly

5.  Install all cover-to-case capscrews and flat washers. Tighten 

the capscrews to 60-75 lb-ft (81-102 Nm).

6.  Recheck the end play. Repeat the end play measurements on 

all shafts. Repeat the adjustment procedures as required.

High and Low Shifter

1.  Grease all o-ring seals. Use a light coat of lithium-based 

grease, Meritor specification O-668. Refer to Figure 7.31 for 
shifter component arrangement.

MTC-4208XL/XLEV/XLEC AND MTC-4210XL/XLEV/XLEC

HIGH RANGE

PORT

4007107a

O-RINGS

LOW

RANGE

PORT

Figure 7.31 

2.  Install o-rings onto the inside diameter and outside diameter 

of the inner piston. Install the inner shift piston and snap ring 
onto the shift shaft. Figure 7.32.

4000193b

INNER
SHIFT
PISTON

Figure 7.32 

3.  Install o-rings onto the inside diameter and outside diameter 

of the outer piston. Install the outer shift piston with the o-ring 
end first to ensure the piston is facing the correct direction.

4.  Install the outer shift piston outer snap ring onto the shift 

shaft. Figure 7.33.

4000192a

OUTER

SHIFT

PISTON

Figure 7.33 

5.  Apply a 1/8” (3 mm) bead of Loctite

®

 277 sealant to the first 

three threads of the shift cylinder.

6.  Install the high and low shift cylinder. Tighten the cylinder to 

80-100 lb-ft (108-136 Nm).

Input Shaft Oil Seal and Yoke

For all transfer cases:

 Install the input seal and sleeve using 

Meritor kits 2728T1 and 2728T2 respectively. Install the forward 
output shaft seal using Meritor Kit 4454.

For MTC-4208X/XL/XP/XLEV/XLEC and MTC-4210X/XL/XP/
XLEV/XLEC transfer cases:

 Install the rear output shaft seal using 

Meritor Kit 4454.

For MTC-4213X transfer case:

 Install the rear output shaft seal 

using Meritor Kit 4454.

 DANGER

Solvent cleaners can be flammable, poisonous, and cause burns. 
Examples of solvent cleaners are carbon tetrachloride, and 
emulsion-type and petroleum-base cleaners. Read the manufac-
turer’s instructions before using a solvent cleaner, then carefully 
follow the instructions. Death or serious personal injury and 
damage to components can result. Follow the procedures below.
 •  Wear eye protection.
 •  Wear clothing that protects the skin.
 •  Work in a well-ventilated area.
 •  NEVER use gasoline or solvents containing gasoline. 
     Gasoline can explode.
 •  Hot solution tanks or alkaline solutions must be used correctly. 
     Read the manufacturer’s instructions before using hot solution 
     tanks and alkaline solutions. Then carefully follow the 
     instructions.

Содержание MM-0861























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды