Meritor MM-0861 Скачать руководство пользователя страница 94

Страница: 94 / 118

MM-0861 / Revised 06-22
Page 92

Printed in USA

10 Troubleshooting

Check oil level, adjust
if necessary, then return
the vehicle to service.

Yes

Remove

leaking seal.

Check the yoke journal for burrs,
rough edges or wear grooves.
Rub down any burrs or rough
spots. If a wear groove is present,
replace the yoke.

1. Check the shaft for

excessive movement.
Repair as necessary.

2. Determine if the transfer

case requires an oil
cooler. Call the Meritor
OnTrac™ Customer Call
Center at 866-OnTrac1
(668-7221) for additional
information.

Check the oil level
in the transfer case.

Too much oil or the incorrect
type of oil can cause the
transfer case to overheat,
which may cause seal damage.

Continued from

previous page.

Road test the vehicle,
then check for leaks.
Return vehicle to service.

Fill the transfer case
with the correct type
and amount of oil.

Check the transfer

case for leaks.

Seal

leaking?

Oil level

too high?

4001526b

Install a new seal using
the correct seal driver.

can cause a seal leak.

NOTE: An incorrect installation

Figure 10.2

Содержание MM-0861























































































































Результаты поиска

Содержание MM-0861

Отзывы:

Бренды по названию

Популярные бренды

Meritor MM-0861, Руководство по обслуживанию

Результаты поиска

Содержание MM-0861

Отзывы:

Бренды по названию

Популярные бренды