manualshive.com logo in svg

Meritor MM-0861, Руководство по обслуживанию

Поделиться
Скачать
Meritor MM-0861 Скачать руководство пользователя страница 62

Copyright Meritor, Inc., 2022

MM-0861  /  Revised 06-22
Page 60

Printed in USA

7     Assembly

Assembly

Hazard Alert Messages

Read and observe all hazard alert messages in this publication. 

 WARNING

To prevent eye injury, always wear eye protection when performing 
vehicle maintenance or service.

 WARNING

Take care when using Loctite

®

 adhesive to avoid serious personal 

injury. Read the manufacturer’s instructions before using this 
product. Follow the instructions carefully to prevent irritation to 
the eyes and skin. If Loctite

®

 adhesive material gets into the eyes, 

follow the manufacturer’s emergency procedures and get 
checked by a physician as soon as possible.

 WARNING

When applying some silicone gasket materials, a small amount of 
acid vapor is present. To prevent serious personal injury, ensure 
the work area is well-ventilated. Read the manufacturer’s 
instructions before using a silicone gasket material, then carefully 
follow the instructions. If a silicone gasket material gets into the 
eyes, follow the manufacturer’s emergency procedures and get 
checked by a physician as soon as possible.

 CAUTION

Although Meritor does not recommend its use in transfer cases, if 
a formed-in-place gasket is used for repairs, extreme caution 
must be exercised to prevent compound from entering bearings, 
oil galleries, and passages or tapped holes. All beads must be 
kept smaller than 0.100” diameter.

Gear and Shaft Sub-Assembly Build Up

Assemble the Front Output Shaft Subassembly

1.  Use an appropriate holding fixture to fully support the shaft 

assembly. Refer to the "Holding Fixture (905473-140)" on 
page 108.

 DANGER

Observe all hazard alerts provided by the press manufacturer. 
Death or serious personal injury and damage to components can 
result.

2.  Use a press and sleeve, tool number 905473-82, to press the 

forward bearing DOWN onto the output shaft until it is fully 
seated. Refer to page 111 for the tool drawing. Press down 
only on the inner race of the bearing during installation. Use a 
0.002” shim or feeler gauge to verify the bearing is correctly 
seated. Figure 7.1. 
 

NOTE:

 Unless otherwise noted, follow the MTC-4208 XLEV 

and MTC-4210 XLEV assembly instructions throughout this 
section for assembly of MTC-4208/10 XLEC variants.

4006923b

PRESS

SLEEVE,

TOOL

905473-82

BEARING

Figure 7.1 

3.  Turn the shaft over and reinstall it into the holding fixture. 

Refer to tool "Holding Fixture (905473-140)" on page 108.

4.  Install the clutch collar. Figure 7.2.

4006924c

SHAFT

CLUTCH

COLLAR

BEARING

HOLDING FIXTURE

TOOL 905473-140

Figure 7.2 

5.  Install the needle bearing onto the rear half of the output 

shaft and lubricate it with a light coat of lithium-based grease, 
Meritor specification O-668. The needle bearing is a slip fit 
assembly. Figure 7.3.

Содержание MM-0861























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды