manualshive.com logo in svg

Meritor MM-0861, Руководство по обслуживанию

Поделиться
Скачать
Meritor MM-0861 Скачать руководство пользователя страница 98

Copyright Meritor, Inc., 2022

MM-0861  /  Revised 06-22
Page 96

Printed in USA

10     Troubleshooting

High/Low Gear Shifting Diagnostics

No

Problem 

fixed?

Turn wheels left and right several times, 
then try to shift into high or low gear.

Check the available air pressure. The transfer case requires
at least 60 psi (4.14 bar) at all times to operate correctly.

Yes

Yes

Yes

Yes

Yes

No

No

Correct system air
pressure.
Refer to the vehicle
OEM instructions.

Check the piston cylinder.
If dirty, disassemble shifter
components for cleaning.
Clear the air supply sytem.
Refer to the vehicle OEM
instructions.
Verify the transfer case
shifts correctly.

No

Remove the shift cylinder and pistons.
Inspect o-rings, pistons, snap rings, and shift bore. 
Repair any damaged components.  
Reassemble and check transfer case shifts correctly.

Air 

pressure 65 psi

(4.48 bar) or

more?

Vehicle

stationary?

Air system

contaminated?

Shift transmission to neutral. 
Shift transfer case to neutral.
Shift transmission into 1st 
gear, press lightly on the
accelerator. (PTO models only) 

Return the vehicle 
to service.

Air blowing

out the housing

breather?

Air blowing

out the neutral

breather or

port?

Yes

No

Return vehicle 
to service.

Reinstall transfer case
in vehicle and return 
vehicle to service. 

Problem 

fixed?

Disassemble transfer case and inspect shift shaft, shift fork, 
shift collar, and shift bore. Repair any damaged components. 
Reassemble and check the transfer case shifts correctly.

Remove the transfer case
from the vehicle. 
Disassemble and replace 
housing o-ring and piston 
o-rings.
Reassemble and verify 
transfer case shifts 
correcly.

Yes

Problem 

fixed?

No

Yes

No

No

Problem 

fixed?

Contact OnTrac™
Customer Call Center at 
866-OnTrac1 (668-7221).

Reinstall transfer case
in vehicle and return
vehicle to service.

Contact OnTrac™
Customer Call Center at 
866-OnTrac1 (668-7221).

No

Yes

4001530c

Return vehicle 
to service.

Return vehicle 
to service.

Figure 10.6 

Содержание MM-0861























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды