manualshive.com logo in svg

Meritor MM-0861, Руководство по обслуживанию

Поделиться
Скачать
Meritor MM-0861 Скачать руководство пользователя страница 65

Copyright Meritor, Inc., 2022

MM-0861  /  Revised 06-22

Page 63

Printed in USA

7     Assembly

4000201c

OIL

RELIEF

PORT

OIL INLET

PORTS

Figure 7.8 

b. Place the bearing cone on the race in the bearing cage.
c. MTC-4208X/XP and MTC-4210X/XP transfer cases only: 

Insert the relief valve and spring into the relief port of the 
input bearing cage. Install the large diameter end of the spring 
down. Figure 7.7. Align the oil pump inlet with the oil inlet port 
of the input bearing cage. Figure 7.8.

d. MTC-4208X/XP and MTC-4210X/XP transfer cases only: 

Install the six pump-to-inlet bearing cage capscrews and 
washers. Apply Loctite

®

 277 sealant to the capscrews. Tighten 

the capscrews to 22-29 lb-ft (29-39 Nm).

e. MTC-4208X/XP and MTC-4210X/XP transfer cases only: 

Lubricate the sealing rings on the inside diameter of the pump 
and the shaft journal adjacent to the pump splines. Figure 7.9.

4005170a

SEALING

RINGS

SNAP

RING

REAR

FORWARD

Sealing rings

can hang-up

on these 

shoulders

Spline side

of gear DOWN

Figure 7.9 

4.  MTC-4208XLEV/XLEC and MTC-4210XLEV/XLEC transfer 

cases only:  

Install the needle bearing on the input shaft. 

Figure 7.10.

MTC-4208XEV/XLEC AND MTC-4210XLEV/XLEC

4011710c

SNAP

RING

OIL

SPACER

NEEDLE BEARING

(XLEV/XLEC ONLY)

LOW-RANGE

HELICAL GEAR

INPUT

SHAFT

Figure 7.10 

5.  Place the low-range helical gear over the input shaft with the 

spline side of the gear down. For MTC-4208XLEV/XLEC and 
MTC-4210XLEV/XLEC, install the oil spacer. The oil spacer 
has two oil channels cut into it. The oil channels can face 
forward or aft when installed. Install the spiral snap ring to 
secure the helical gear. The gear is a slip fit. Figure 7.10.

6.  Lubricate the gear and shaft before assembly. 

7. 

MTC-4208XL/XLEV/XLEC and MTC-4210XL/XLEV/XLEC 
transfer cases only:

 Install the high- and low-range clutch 

collar over the input shaft splines. Place the high-range helical 
gear over the input shaft with the spline side of the gear 
facing the low-range helical gear. Install the bearing cone with 
the large end of the cone toward the high-range gear. Install 
the spacer on the shaft next to the bearing cone. Figure 7.11.

4011710d

INPUT

SHAFT

BEARING

NUT

SPACER

HIGH-RANGE

HELICAL GEAR

HIGH AND LOW

 

RANGE CLUTCH COLLAR

Figure 7.11 

 CAUTION

Exercise care when assembling the input shaft to the pump. Line 
up and slowly direct the input shaft into the pump opening. 
Misalignment during assembly can cause the shaft to “hang up” 
on the pump sealing rings resulting in damage to the rings.

NOTE: 

Use care when installing the input bearing cage to prevent 

damage to the o-ring.

Содержание MM-0861























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды