Meritor MM-0861 Скачать руководство пользователя страница 85

Страница: 85 / 118

MM-0861 / Revised 06-22

Page 83

Printed in USA

8 Power Takeoff (PTO)

Install the Yoke onto the PTO

A Meritor yoke with the spline code “RAI” must be installed onto
the PTO. For yoke options, refer to Table E and Figure 8.3.

Table E: PTO Yoke Options and Dimensions

Part #

17NYS32-100A1

17TYS32-68A1

Yoke Type

Full Round

Easy Service™

Center to
End

5.16”
(131 mm)

5.47”
(139 mm)

Spline
Length

2.32”
(59 mm)

Hub
Diameter

3.00”
(76 mm)

Bearing
Diameter

1.94”
(49 mm)

Across
Ears

6.00”
(152 mm)

6.20”
(157 mm)

Spline
Size

2.00 x 39”
(51 x 991 mm)

4000220b

PART NUMBER

17NYS32100A1

FULL ROUND

YOKE (NYS)

PART NUMBER

17TYS3268A1

EASY SERVICE

YOKE (TYS)

Refer to Table E

for Yoke Dimensions

Figure 8.3

1. Use a press and an applied press force of 500-1500 lbs

(227-680 kg) to install a Meritor yoke, spline code RAI, onto
the PTO shaft. Figure 8.2.

2. Apply a 1.8” (46 mm) bead of RTV silicone gasket material

around the end of the yoke spline under the washer surface.

3. Install the washer and locknut supplied in the kit. Tighten the

lock nut to 700-900 lb-ft (949-1220 Nm).

Install the Optional Indicator Switch

Table F: PTO Switch Option

Part #

3237-W-1167

Part Name

Switch and Connector Assembly

Description

2 Amp x 12 VDC, M16 x 1” thread

Qty

1. Remove the screw and washer from the end of the PTO cap.

Figure 8.4.

4000215a

SWITCH

PORT SCREW

AND WASHER

OPTIONAL

CONNECTOR

SWITCH

ASSEMBLY

AIR CONTROL

PORT

Figure 8.4

2. Apply Loctite

518 gasket sealant to the indicator switch

threads.

3. Install the indicator switch. Tighten the switch to 25-30 lb-ft

(34-41 Nm). Figure 8.5.

4000216a

OPTIONAL

CONNECTOR

SWITCH

ASSEMBLY

SPECIAL PLUG

AND WASHER

AIR

CONTROL

PORT

INDICATOR

SWITCH

Figure 8.5

Содержание MM-0861























































































































Результаты поиска

Содержание MM-0861

Отзывы:

Бренды по названию

Популярные бренды

Meritor MM-0861, Руководство по обслуживанию

Результаты поиска

Содержание MM-0861

Отзывы:

Бренды по названию

Популярные бренды