manualshive.com logo in svg

Meritor MM-0861, Руководство по обслуживанию

Поделиться
Скачать
Meritor MM-0861 Скачать руководство пользователя страница 63

Copyright Meritor, Inc., 2022

MM-0861  /  Revised 06-22

Page 61

Printed in USA

7     Assembly

4006924d

NEEDLE
BEARING
ASSEMBLY

Figure 7.3 

6.  Install the helical gear onto the shaft. The helical gear is a slip 

fit gear.

7.  Remove the shaft from the holding fixture and install it into a 

press. Correctly support the shaft in the press.

8.  Use tool number 905473-92 to install the bearing onto the top 

of the output shaft with the small tapered end UP. Use a press 
and sleeve to push the bearing DOWN onto the output shaft 
until it is fully seated. Refer to page 109 for the tool drawing. 
Press down only on the inner race of the bearing during 
installation. Use a 0.002” shim or feeler gauge to verify the 
bearing is correctly seated. Figure 7.4.

4006926b

SLEEVE,

TOOL

905473-92

HELICAL

GEAR

BEARING

PRESS

Figure 7.4 

 DANGER

Follow all safety guidelines and instructions provided by the lifting 
device manufacturer. Inspect lifting straps to ensure they are not 
damaged. NEVER subject lifting straps to shocks or drop-loading. 
Death or serious personal injury and damage to components can 
result.

9.  Remove the output shaft from the press and reinstall it into the 

holding fixture. Refer to tool "Holding Fixture (905473-140)" on 
page 108. Use an appropriate lifting device to lift the shaft.

10.  Lubricate the output shaft threads with SAE Grade full-

synthetic 40W or 50W oil, Meritor specification O-81.

11.  Install the washer and the locknut onto the shaft. Tighten the 

locknut to 700-900 lb-ft (949-1220 Nm). Figure 7.5.

HOLDING FIXTURE

TOOL 905473-140

LOCKNUT

4006927a

WASHER

Figure 7.5 

Assemble the Single Idler Gear Subassembly  
(MTC-4213X Only)

1.  Install the shaft assembly into a press and support it correctly 

with the forward end facing UP.

2.  Place the bearing onto the forward end of the shaft assembly.  

Use a sleeve, "Bearing Cone Driver (905473-82)" on page 
111, and press to push the forward bearing cone DOWN 
until it is fully seated. Only press on the inner race of the 
bearing cone. Use a 0.002” shim or feeler gauge to ensure 
the bearing cone is correctly seated.

3.  Rotate the shaft so the rear half of the shaft is facing UP. Use 

a sleeve, tool number 905473-92, and press to push the 
rear bearing cone DOWN until it is fully seated. Refer to page 
109 for the tool drawing. Only press on the inner race of the 
bearing cone. Use a 0.002” shim or feeler gauge to ensure 
the bearing cone is correctly seated.

Assemble the Rear Output Shaft Subassembly  
(MTC-4208X/XP/XL/XLEV/XLEC and MTC-4210X/XP/
XL/XLEV/XLEC Only)

1.  Install the shaft assembly into a press and support it correctly.

2.  Place the bearing cone onto the end of the shaft assembly 

with the appropriate end facing UP. Use a sleeve, "Bearing 
Cone Driver (905473-82)" on page 111, and press to push 
the bearing cone DOWN until it is fully seated. Only press 
on the inner race of the bearing cone. Use a 0.002” shim or 
feeler gauge to ensure the bearing cone is correctly seated.

3.  Turn the shaft assembly over and install the bearing cone on 

the other end using Steps 1-2.

Содержание MM-0861























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды