Meritor MM-0861 Скачать руководство пользователя страница 92

Страница: 92 / 118

MM-0861 / Revised 06-22
Page 90

Printed in USA

9 Installation

MTC-4208/10 XLEC Crossover Tube Installation for
Driver-Side Mounted Cooler (Connection at 1:00 Position)

1. Install the tee fitting onto the front case idler bearing oil supply

port elbow fitting. Tighten the tee fitting to 20 lb-ft (54 Nm).
Figure 9.5.

OIL PUMP

CROSSOVER

TUBE

TEE FITTING

OE COOLER LINE

CONNECTION

4016827b

P-CLAMP
ASSEMBLY

MTC-4208/10 XLEC DRIVER SIDE MOUNTED COOLER

Figure 9.5

2. Install the new oil pump crossover tube to the tee fitting on the

front case half. Tighten the tube nut to 20 lb-ft (27 Nm). Figure 9.5.

3. Reconnect the OE chassis cooler return hose to the tee fitting on

the front case half at the idler front bearing position. Tighten the
hose nut to 40 lb-ft (54 Nm). Figure 9.5.

4. Connect the oil pump crossover tube from the front case to the

pump outlet fitting on the rear case half. Tighten the tube nut to
20 lb-ft (27 Nm). Figure 9.6.

OIL PUMP

CROSSOVER

TUBE

4016828a

Figure 9.6

5. Remove the housing capscrew and install through the angle

bracket as shown in Figure 9.5. Apply Loctite

242 to the first 3

threads, reinstall, and tighten to 60-75 lb-ft (81-102 Nm). Place
the P-clamp around the oil pump crossover tube and, using the
supplied socket head bolt and lock nut, attach it to the angle
bracket and tighten to 8-10 lb-ft (11-14 Nm).

NOTE:

The P-clamp bracket is intended to support the crossover

tube. Make certain there is no tension applied to the crossover
tube once the fasteners have been tightened.

MTC-4208/10 XLEC Crossover Hose Installation
for Passenger-Side Mounted Cooler
(Connection at 9:00 Position)

1. Install the tee fitting onto the front case idler bearing oil supply

port elbow fitting. Tighten the tee fitting to 20 lb-ft (54 Nm).
Figure 9.7.

OIL PUMP

CROSSOVER

TUBE

4016829b

P-CLAMP
ASSEMBLY

MTC-4208/10 XLEC PASSENGER SIDE MOUNTED COOLER

Figure 9.7

2. Install the new oil pump crossover tube to the tee fitting on the front

case half. Tighten the tube nut to 20 lb-ft (27 Nm). Figure 9.7.

3. Reconnect the OE chassis cooler return hose to the tee fitting on

the front case half at the idler front bearing position. Tighten the
hose nut to 40 lb-ft (54 Nm). Figure 9.7.

4. Connect the oil pump crossover tube from the front case to the

pump outlet fitting on the rear case half. Tighten the tube nut to
20 lb-ft (27 Nm). Figure 9.8.

OIL PUMP

CROSSOVER

TUBE

4016830a

Figure 9.8

5. Remove the housing capscrew and install through the angle

bracket as shown in Figure 9.7. Apply Loctite

242 to the first 3

NOTE:

The P-clamp bracket is intended to support the crossover

tube. Make certain there is no tension applied to the crossover
tube once the fasteners have been tightened.

Содержание MM-0861























































































































Результаты поиска

Содержание MM-0861

Отзывы:

Бренды по названию

Популярные бренды

Meritor MM-0861, Руководство по обслуживанию

Результаты поиска

Содержание MM-0861

Отзывы:

Бренды по названию

Популярные бренды