Mercury 25 Jet FourStroke Скачать руководство пользователя страница 96

Страница: 96 / 110

IMPORTANT: Determine the strength of the boat transom. The outboard

mounting locknuts and bolts should be able to hold 75 Nm (55 lb‑ft) of torque

without the boat transom yielding or cracking. If the boat transom yields or

cracks under this torque, the construction of the transom may not be adequate.

The boat transom must be strengthened or the load carrying area increased.

a -

Transom yielding under bolt torque

b -

Transom cracking under bolt torque

When first determining transom strength, use a dial torque wrench. If the bolt or

nut continues to turn without the torque reading on the dial increasing, it is an

indication that the transom is yielding. The load area can be increased by using

a larger washer or a transom reinforcement plate.

NOTE: The inside holes on the transom reinforcement plate are for the lower

transom bolts and the outside holes are for the upper transom bolts.

a -

Large transom washer

b -

Transom reinforcement plate

1. Drill four 13.5 mm (17/32 in.) mounting holes.
2. Install the outboard so that the water intake housing is set at the correct

height. Refer to

Determining the Mounting Height of the Outboard Jet

3. Apply marine sealer to shanks of bolts. Do not apply marine sealer to the

threads of the bolts.

18961

20860

INSTALLATION

eng

Содержание 25 Jet FourStroke















































































































Результаты поиска

Содержание 25 Jet FourStroke

Отзывы:

Похожие инструкции для 25 Jet FourStroke

Бренды по названию

Популярные бренды

Mercury 25 Jet FourStroke, Руководство по эксплуатации, техническому обслуживанию и установке

Результаты поиска

Содержание 25 Jet FourStroke

Отзывы:

Похожие инструкции для 25 Jet FourStroke

Бренды по названию

Популярные бренды