Mercury 25 Jet FourStroke Скачать руководство пользователя страница 57

Страница: 57 / 110

Gear Shifting

NOTE: The propeller continues to rotate while the engine is in neutral. Although

the approximate balancing of forward and reverse thrust will minimize boat

movement, the boat may tend to move slowly forward and backward. This is

normal for a direct‑drive jet driven boat. The operator should be aware of this

and use caution whenever the engine is running.

•

The outboard has three gear shift positions to provide operation: forward

(F), neutral (N), and reverse (R).

•

Tiller handle models

‑ Reduce the engine speed to idle before shifting.

START

24834

24835

•

Remote control models

‑ When shifting, always stop at the neutral

position and allow the engine speed to return to idle.

27237

•

After shifting the outboard into gear, advance the remote control lever or

rotate the throttle grip (tiller handle) to increase speed.

OPERATION

eng

Содержание 25 Jet FourStroke















































































































Результаты поиска

Содержание 25 Jet FourStroke

Отзывы:

Похожие инструкции для 25 Jet FourStroke

Бренды по названию

Популярные бренды

Mercury 25 Jet FourStroke, Руководство по эксплуатации, техническому обслуживанию и установке

Результаты поиска

Содержание 25 Jet FourStroke

Отзывы:

Похожие инструкции для 25 Jet FourStroke

Бренды по названию

Популярные бренды