Mercury 25 Jet FourStroke Скачать руководство пользователя страница 62

Страница: 62 / 110

Tube Ref

No.

Description

Where Used

Part No.

120

Corrosion Guard

External metal surfaces of the powerhead

and powerhead components.

92-802878 55

EPA Emission Regulations

All new outboards manufactured by Mercury Marine are certified to the United

States Environmental Protection Agency, as conforming to the requirements of

the regulations for the control of air pollution from new outboard motors. This

certification is contingent on certain adjustments set to factory standards. For

this reason, the factory procedure for servicing the product must be strictly

followed and, wherever practicable, returned to the original intent of the design.

Maintenance, replacement, or repair of the emission control devices and
systems may be performed by any marine spark ignition (SI) engine
repair establishment or individual.

EMISSION CERTIFICATION LABEL

An emission certification label, showing emission levels and engine

specifications directly related to emissions, is placed on the engine at time of

manufacture.

a -

Piston displacement

b -

Maximum emission output for the engine family

c -

Percent of fuel line permeation

d -

Timing specification

e -

US EPA engine family name

f -

Horsepower rating

g -

Engine power ‑ kilowatts

h -

Idle speed (in gear)

OWNER RESPONSIBILITY

The owner/operator is required to have routine engine maintenance performed

to maintain emission levels within prescribed certification standards.

2008

JAN

FEB

MAR

APR

MAY

JUN

JUL

AUG

SEP

OCT

NOV

DEC

THIS ENGINE CONFORMS TO 2010 CALIFORNIA AND U.S. EPA EMISSION

REGULATIONS FOR SPARK IGNITION MARINE ENGINES. REFER TO OWNER’S

MANUAL FOR REQUIRED MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.

PLEASE PERFORM THE ENGINE MAINTENANCE CORRECTLY.

FAMILY :

MERCURY MARINE

EMISSION CONTROL INFORMATION

DISPLACEMENT :
FEL : HC+NOx=

LOW-PERM/HIGH-PERM :

TIMING :

IDLE SPEED (IN GEAR) :

MAXIMUM POWER :

HP :

2008

43058

CO=

MAINTENANCE

eng

Содержание 25 Jet FourStroke















































































































Результаты поиска

Содержание 25 Jet FourStroke

Отзывы:

Mercury 25 Jet FourStroke, Руководство по эксплуатации, техническому обслуживанию и установке, Страница: 62 / 110

Результаты поиска

Содержание 25 Jet FourStroke

Отзывы: