Mercury 25 Jet FourStroke Скачать руководство пользователя страница 90

Страница: 90 / 110

Installation Information

MERCURY MARINE VALIDATED ENGINE MOUNTING HARDWARE

IMPORTANT: Mercury Marine provides validated fasteners and installation

instructions, including torque specifications, with all of our outboards so they

can be properly secured to boat transoms. Improper installation of the outboard

can cause performance and reliability issues that can lead to safety concerns.

Follow all of the instructions relating to the outboard installation. DO NOT

mount any other accessory onto the boat with the fasteners provided with the

outboard. For example, do not mount tow sport bars or boarding ladders onto

the boat using the mounting hardware included with the outboard. Installing

other products onto the boat that utilize the outboard mounting hardware will

compromise the ability of that hardware to properly and safely secure the

outboard to the transom.
Outboards that require validated mounting hardware will have the following

decal on the transom clamp.

51965

BOAT HORSEPOWER CAPACITY

WARNING

Exceeding the boat's maximum horsepower rating can cause serious injury

or death. Overpowering the boat can affect boat control and flotation

characteristics or break the transom. Do not install an engine that exceeds

the boat's maximum power rating.

INSTALLATION

eng

Содержание 25 Jet FourStroke















































































































Результаты поиска

Содержание 25 Jet FourStroke

Отзывы:

Mercury 25 Jet FourStroke, Руководство по эксплуатации, техническому обслуживанию и установке, Страница: 90 / 110

Результаты поиска

Содержание 25 Jet FourStroke

Отзывы: