Mercury 25 Jet FourStroke Скачать руководство пользователя страница 69

Страница: 69 / 110

6. Install the water intake housing with six bolts. Check clearance around the

impeller to ensure the water intake housing is centered and not rubbing

against the liner. Tighten the mounting bolts to the specified torque.

29081

Description

lb‑in.

lb‑ft

Water intake housing mounting bolts

13.5

120

–

Shift Link Rod Adjustment

WARNING

Pressurized water hitting the reverse gate may cause it to engage, causing

sudden and unexpected slowing of the boat. This can cause serious injury or

death from occupants being thrown within or out of the boat. Adjust the shift

link rod to lock the reverse gate, preventing it from interfering with water flow.

CHECKING SHIFT LINK ROD ADJUSTMENT

Check the shift link rod adjustment in forward shift position. The correct

adjustment will position the shift cam far enough on the roller in order to lock

the reverse gate into forward position. The reverse gate should not be able to

be forced up towards neutral. Pull on the reverse gate by hand to verify.

a -

Shift link rod

b -

Shift cam

c -

Roller

d -

Reverse gate

ADJUSTING SHIFT LINK ROD

1. Place the shift handle into full forward shift position.

29084

MAINTENANCE

eng

Содержание 25 Jet FourStroke















































































































Результаты поиска

Содержание 25 Jet FourStroke

Отзывы:

Похожие инструкции для 25 Jet FourStroke

Бренды по названию

Популярные бренды

Mercury 25 Jet FourStroke, Руководство по эксплуатации, техническому обслуживанию и установке

Результаты поиска

Содержание 25 Jet FourStroke

Отзывы:

Похожие инструкции для 25 Jet FourStroke

Бренды по названию

Популярные бренды