Mercury 25 Jet FourStroke Скачать руководство пользователя страница 39

Страница: 39 / 110

TILTING OUTBOARD TO FULL UP POSITION

1. Stop the engine. Move the lock lever to the free position. Take hold of the

top cowl grip and raise the outboard to the full tilt up position. Lock the

outboard in place by moving the lock lever to the lock position.

10284

2. Engage the tilt support lever.
3. Lower the outboard to rest on the tilt support lever.

LOWERING OUTBOARD TO RUN POSITION

1. Move the lock lever to the free position. Tilt up the outboard slightly and

release the tilt support lever. Lower the outboard to the run position.

2. Move the lock lever to the lock position.

9703

OPERATING ANGLE ADJUSTMENT

The transom brackets have four holes for adjusting the vertical operating angle

(forward stop movement) of the outboard. Use the tilt pin for adjustments in the

four holes.

a -

Transom bracket holes

b -

Tilt pin

LOCK

FREE

10290

FEATURES AND CONTROLS

eng

Содержание 25 Jet FourStroke















































































































Результаты поиска

Содержание 25 Jet FourStroke

Отзывы:

Похожие инструкции для 25 Jet FourStroke

Бренды по названию

Популярные бренды

Mercury 25 Jet FourStroke, Руководство по эксплуатации, техническому обслуживанию и установке

Результаты поиска

Содержание 25 Jet FourStroke

Отзывы:

Похожие инструкции для 25 Jet FourStroke

Бренды по названию

Популярные бренды