Mercury 25 Jet FourStroke Скачать руководство пользователя страница 9

Страница: 9 / 110

Storage

Storage Preparation..........................................................................................72

Protecting External Outboard Components...................................................... 72

Protecting Internal Engine Components........................................................... 73

Jet Drive............................................................................................................73

Positioning Outboard for Storage..................................................................... 73

Battery Storage................................................................................................. 73

Troubleshooting

Starter Motor will not Crank the Engine (Electric Start Models)........................74

Engine Will Not Start.........................................................................................74

Engine Runs Erratically.................................................................................... 74

Engine Overspeed (Excessive RPM)............................................................... 75

Performance Loss.............................................................................................75

Battery Will Not Hold Charge............................................................................ 75

Owner Service Assistance

Service Assistance........................................................................................... 76

Ordering Literature............................................................................................78

Installation

Installation Information......................................................................................80

Top Cowl Removal and Installation.................................................................. 82

Lifting Outboard................................................................................................ 83

Determining the Mounting Height of the Outboard Jet .................................... 83

Fastening the Outboard.................................................................................... 85

Steering Bracket, Steering Cable Installation................................................... 87

Steering Link Rod Fasteners............................................................................ 88

Electrical Harness, Battery Connection, Fuel Tanks........................................ 91

Control Cable Installation..................................................................................94

Water Testing................................................................................................... 98

Maintenance Log

Maintenance Log............................................................................................ 100

eng

vii

Содержание 25 Jet FourStroke















































































































Результаты поиска

Содержание 25 Jet FourStroke

Отзывы:

Mercury 25 Jet FourStroke, Руководство по эксплуатации, техническому обслуживанию и установке, Страница: 9 / 110

Результаты поиска

Содержание 25 Jet FourStroke

Отзывы: