Mercury 25 Jet FourStroke Скачать руководство пользователя страница 42

Страница: 42 / 110

Turn out the manual tilt release valve three turns counterclockwise. This allows

manual tilting of the outboard. Tilt the outboard to the desired position and

tighten the manual tilt release valve.

9976

AUXILIARY TILT SWITCH

The auxiliary tilt switch can be used to tilt the outboard up or down using the

power trim system.

9974

SHALLOW WATER OPERATION

When operating your boat in shallow water, you can tilt the outboard beyond

the maximum trim range to prevent hitting bottom.

1. Reduce the engine speed below 2000 RPM.
2. Tilt the outboard up. Make sure all the water intake holes stay submerged

at all times.

3. Operate the engine at slow speed only.

Warning System

WARNING HORN

Remote control models have a warning horn located inside the remote control

or connected to the ignition key switch. Tiller handle models have a warning

horn located in the engine cowl.

FEATURES AND CONTROLS

eng

Содержание 25 Jet FourStroke















































































































Результаты поиска

Содержание 25 Jet FourStroke

Отзывы:

Mercury 25 Jet FourStroke, Руководство по эксплуатации, техническому обслуживанию и установке, Страница: 42 / 110

Результаты поиска

Содержание 25 Jet FourStroke

Отзывы: