Mercury 25 Jet FourStroke Скачать руководство пользователя страница 74

Страница: 74 / 110

1. Remove the spark plug leads. Twist the rubber boots slightly and pull off.

26899

2. Remove the spark plugs to inspect. Replace spark plug if electrode is

worn or the insulator is rough, cracked, broken, blistered, or fouled.

26946

3. Set the spark plug gap to specifications.

27848

Spark Plug Gap
Spark plug

0.80–0.90 mm (0.031–0.035 in.)

4. Before installing spark plugs, clean off any dirt on the spark plug seats.

Install plugs finger‑tight, and then tighten to the specified value.

Description

lb‑in.

lb‑ft

Spark plug

177

–

Fuse Replacement ‑ Electric Start Models

IMPORTANT: Always carry spare SFE 20 amp fuses.
The electric starting circuit is protected from overload by an SFE 20 amp fuse.

If the fuse is blown, the electric starter motor will not operate. Try to locate and

correct the cause of the overload. If the cause is not found, the fuse may blow

again.

MAINTENANCE

eng

Содержание 25 Jet FourStroke















































































































Результаты поиска

Содержание 25 Jet FourStroke

Отзывы:

Похожие инструкции для 25 Jet FourStroke

Бренды по названию

Популярные бренды

Mercury 25 Jet FourStroke, Руководство по эксплуатации, техническому обслуживанию и установке

Результаты поиска

Содержание 25 Jet FourStroke

Отзывы:

Похожие инструкции для 25 Jet FourStroke

Бренды по названию

Популярные бренды