Megger PPX30 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 84

Megger PPX30 Скачать руководство пользователя страница 57

8. A dialog box will appear with a warning that the voltage will lock and start at the target voltage level for all

subsequent tests, overriding the zero-volt interlock feature.

Fig 46:

Zero start override warning message.

9. Move the test fixture (or probes) to the second bar pairing (2–3).

10. Press the

Test (PTT)

button or footswitch. The analyzer will energize Lead 1 at the preset voltage and the

waveform will be displayed on the screen as the red wave. The reference is also displayed as the blue waveform.
A reference-to-bar EAR value will be displayed in the

Ref Bar EAR

field.

11. If the EAR percentage is greater than the tolerance, the field background will turn red indicating a failed test. If

the EAR percentage is under or equal to the tolerance, the background of the

Ref-Bar EAR

box will be white,

indicating a passing test.

12. When you are satisfied with the waveform, release the fixture’s test button or footswitch. The EAR percentage

will be saved and an inset bar graph will be displayed depicting the EAR percentage versus the reference bar’s
waveform. If the bar failed, the EAR bar on the graph will be red.

13. Up to three additional waveforms can be saved during the testing process. If a bar fails or is of interest, click

on one of the

Save

button in the

Save Waveforms

section at the top of the screen and that waveform will be

saved along with its bar number; otherwise, only the reference-to-bar EAR percentage for the bar will be saved.

14. Continue to move the test fixture to the next bar and repeat the process from step 10 for each bar until all bars

have been tested. A maximum of 1,024 bars can be tested.

15. If at any time before you save the full test results you want to retest a bar, you can enter that bar number

directly into the

Bar Control

field, or use the up and down arrows to navigate to the bar number, and retest as

needed. Retesting will overwrite the previous data for that bar.

16. The

Total Bars Tested

number gives you the number of the last bar tested. Add one to that number to resume

testing where you left off.

Using Power Packs with Baker AWA Testers

www.megger.com 49

«
...
55
56
57
58
59
...
»

Содержание PPX30





















































































Отзывы:

Нет отзывов