Megger PPX30 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 84

Megger PPX30 Скачать руководство пользователя страница 13

2 — Baker Power Pack Introduction

Instrument Notices

CAUTION: Be sure to comply with all safety and proper operating procedures when setting up the tester and power
packs, and when using them in testing. Failure to do so can result in injury to personnel or damage to equipment.

General

The host testers are equipped with open ground/ground fault monitors and indicators. This circuitry should not
hinder operation of GFI protected AC power circuits.

When the analyzer is plugged into the power pack as described later in this guide, it gets its AC power from the
power pack; so if the power pack is unplugged, the analyzer will also turn off.

Before use:

Do not allow the analyzer’s test leads to lie anywhere near the power pack test leads. The unit’s leads should
coil on top of the unit or loop on the power pack handle. Otherwise, the leads could interfere with tester
measurements.

Make sure the analyzer’s test leads are not connected together.

Make sure the analyzer’s (host) ground test lead is not grounded when conducting tests using a power pack.

Make sure no printer is hooked up to the USB port.

During use:

Do not switch the test leads or change the

Test Select

switch while a test is in progress.

If you need to use the host unit in standalone mode, turn off the power pack, ensure that the analyzer’s AC
input is plugged into a properly grounded source, and disconnect the communications cable between the
analyzer and the power pack. If the communications cable between the analyzer and the power pack remains
connected and the power pack is turned off, the I/O lines will be influenced and will cause problems with the
analyzer’s operation.

NOTICE: A power pack is purchased with, and calibrated to, the Baker DX or Baker AWA-IV tester host that it is
shipped with.

Baker Power Pack Introduction

www.megger.com 5

«
...
11
12
13
14
15
...
»

Содержание PPX30





















































































Отзывы:

Нет отзывов