Megger PPX30 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 84

Megger PPX30 Скачать руководство пользователя страница 39

Single-phase Testing—PPX30/30A Combined with Baker AWA Tester

When performing single-phase testing (for example , on DC motors or when testing single coils) you must use the

Temperature/Resistance Test

setup window to define the parameters that instruct the tester to operate in single-

phase testing mode.

NOTE: The parameters set in the Temperature/Resistance Test setup window affect only the Megohm and DA/PI tests
because the AWA test leads are used for these tests when used in combination with a PPX30/30A tester. The power
pack’s test leads are used, in turn, for DC HiPot and Surge testing, which are not controlled by the AWA’s setup
windows.

The Temperature/Resistance Test setup window is the only place where you specifically define parameters to enable
single-phase testing for the Baker AWA host unit.

1. Click on the test configuration button at the end of the second/Resistance row in the

Temperature/Resistance

Tests

section.

2. Click on the

Temperature Enable

radio button if you will be using temperature compensation.

3. Click on the

Resistance Enable

radio button to enable the parameter options in this area.

4. Click on

2 Leads (1 phase)

and check the

Res Leads

box. Notice that the list of leads to test in the

Test Results

section changes to include only one test lead set (Lead 1–2).

5. You can leave the

Resistance Enable

radio button active if you choose to run resistance tests, or turn it off if

not. However, you must ensure that the

2 Leads (1 phase)

radio button is selected and the

Res Leads

box is

checked to enable single-phase testing.

Fig 27:

Setting up the Resistance Test parameters for single-phase testing.

CAUTION: As noted above, the PPX30/30A test leads are used during DC HiPot and Surge testing, and they are not
controlled by the “2 leads” setting defined in the Temperature/Resistance Test setup window. The power pack’s test
leads should always be treated as energized leads when handling them.

Using Power Packs with Baker AWA Testers

www.megger.com 31

«
...
37
38
39
40
41
...
»

Содержание PPX30





















































































Отзывы:

Нет отзывов