background image

Controls, Connectors, Indicators & Menus 

 

 
AVTMBITE 3 Rev 8 April 2014 

13 

The Battery Module 

The battery module contains nickel-metal-hydride cells and has a built-in battery-
management system that controls charging and monitors discharge. This 
provides a high capacity, low-weight battery system, which can be recharged at 
any time. It is not possible for the user to over-charge or over discharge the 
battery. For your own convenience it is best to charge it regularly to keep it 
topped up, but leaving it in a discharged state will do no harm. 

On the front of the battery module are two buttons and a 10-segment LED 
display. To find the amount of charge in your battery module, whether 
connected to your BITE 3 or separate, press the 

Battery Condition

 button.  

 

Figure-4:  BITE 3 Battery Charger Condition  

The 

Battery State Indicator

 will light between 1 and 10 segments signifying between 

10% and 100% charge respectively. After a few seconds this display will 
automatically go out. 

NOTE: 

The batteries are nickel-metal-hydride and if these are changed the 
disposal of cells should be in accordance with local regulations. 

Battery Charging 

Please note - The battery should only be charged within the temperature range 
32°F – 115°F (0°C to 45°C). Fast charging will not be allowed if the temperature 
is below 10°C. Fast charging causes the temperature of the battery to rise. If the 
temperature exceeds 115°F (45°C) the charging rate will be reduced 
automatically. 

To charge the battery, your battery module must be removed from the 
instrument. Remove the module by pressing on the raised circular area of the 
retaining clips and pull the top of the clip away from the instrument body. The 
module now unplugs from the base of the instrument. Plug in the charger (J4) or 
connect the optional 12 volt vehicle-type battery using the ‘cigarette lighter’ lead. 
The LED "Battery State" indicator will light and show movement when the 
battery is charging. The battery may be recharged before it has been fully 

J6 

J5

Содержание BITE 3











































Отзывы: