Meech IonWash Скачать руководство пользователя страница 24

Страница: 24 / 56

2. Positive pressure target set pressure value and setting buttons

The ‘+’ and ‘-‘ buttons are used to set the Positive Pressure level. The target value is shown in kPa just above the

buttons. This is also represented by the arrow shown in the Positive Pressure level indicator

3. System Status Indicator

The System status indicator displays if the system is running or stopped.

4. Filter Status Indicator

The filter status indicator displays the filter status. When the filter is clean the filter status will be green and display

‘Filter OK’, when the filter is dirty (but not blocked) the status will turn orange and display ‘Filter Dirty’; and when

the filter is blocked and will need cleaning or replacing the filter status will turn red and display ‘Filter Blocked’.

5. Local/Remote toggle buttons

The Local and Remote buttons are used to switch between the screen controlling the pumps or the manual push

buttons controlling the whole IonWash.

For standard operation, the IonWash needs to be in Local mode.

For cleaning/maintenance cycles and testing the screen can be placed in to local mode which will allow the pumps

to run without the doors coming down.

Содержание IonWash

























































Результаты поиска

Содержание IonWash

Отзывы:

Похожие инструкции для IonWash

Бренды по названию

Популярные бренды

Meech IonWash, Руководство по эксплуатации

Результаты поиска

Содержание IonWash

Отзывы:

Похожие инструкции для IonWash

Бренды по названию

Популярные бренды