Mecmesin AFTI Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 47

background image

AFG/AFTI Mk 4

Service and Repair Manual

Number 022-614

Issue Number: 09

Page 31 of 47

2) Remove load sign change feature in calibration routine. (Flyspray ID76)

- The calibration routine contains a feature that allows the load sign to be
changed if the load cell has been wired incorrectly. However, although it alters
it for the digital side of the gauge, the polarity of the analogue output remains
incorrect. Therefore the feature needs to be removed so that if a load cell is
wired incorrectly, the load cell should be removed and wired the correct way.

Implemented in version 1.04 (DCR1464) from serial number 08-0168-08
-------------------------
1) Auto-off Eeprom address (Flyspray ID27)

- Auto-off eeprom address moved as overwrote Rate in eeprom

causing gauge to enter 'High Rate' mode which was perceived

as noise in the Orbis

2) Zero Blanking (Flyspray ID28)

- Zero blanking added for high rate so that any load to be

displayed that is less than the accuracy of the gauge is

displayed as zero

3) Loadbar sign (Flyspray ID29)

- Loadbar now always correct appearance

4) Calibration in non-SI units (Flyspray ID40)

- Calibration routine allows calibration in units other than

N and Nm

Implemented in version 1.03 (DCR1444)
-------------------------

1) Calibration Routine

- Calibration routine not entered if Smart connected

2) Turning on with Smart connected

- Delay added to allow hardware to switch to Smart load

3) Torque Smarts

- Smart Torques displayed as correct type and not as force

Implemented in version 1.02 (DCR 1434) (Not Released)
-------------------------

1) Calibration Routine

- Low battery symbol check added to calibration routine

«
...
29
30
31
32
33
...
»

Содержание AFTI
















































Отзывы:

Нет отзывов

Похожие инструкции для AFTI

Бренд: Teac Страницы: 148

Бренд: IFM Страницы: 25

Бренд: Campbell Страницы: 16

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 4

Бренд: Hanna Instruments Страницы: 2

Бренд: HANYOUNGNUX Страницы: 4

Бренд: +GF+ Страницы: 8

Бренд: S.E. International Страницы: 30

Бренд: SZBJ Страницы: 2

Бренд: LEM Страницы: 33

STORA-ABG RKS-01

Бренд: ECOTEST Страницы: 146

Vigilant Plant MR20000

Бренд: YOKOGAWA Страницы: 230

CR-2010 PRO Series

Бренд: G-Tek Страницы: 48

Бренд: HTC Страницы: 2

Бренд: TESTO Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды