Mecmesin AFTI Скачать руководство пользователя страница 2

Страница: 2 / 47

AFG/AFTI Mk 4

Service and Repair Manual

Number 022-614

Issue Number: 09

Page 2 of 47

PDF copy stored in approved

location by: (click on signature for

validation)

Paper copy printed from approved PDF source

by:

Name

Signature

Date

1. Contents

Contents .............................................................................................................. 2

Change History .................................................................................................... 3

Product variants .................................................................................................. 4

Warnings and cautions: - ..................................................................................... 5

Latest software version: - V1.12 .......................................................................... 5

Inspection procedure ........................................................................................... 6

Notes about 300-157-V03 ................................................................................... 8

PCB replacement (300-157-V02/3) ..................................................................... 9

Sounder replacement (328-005) ........................................................................ 12

10.

Display replacement (301-028-V01) ............................................................... 13

11.

Configuration of display 301-028 V1.06

– V1.10 ............................................. 14

12.

Configuration of Display 301-028-V01 (V1.12) ............................................... 19

13.

Charging socket replacement (329-355) ......................................................... 22

14.

Keypad Membrane/Front Cover Plate replacement ........................................ 23

15.

Load cell removal ............................................................................................ 24

16.

Load cell stud fitting. ....................................................................................... 25

17.

Load cell refitting ............................................................................................. 27

18.

Battery lid/insulator replacement ..................................................................... 27

19.

Firmware version

– Identification. ................................................................... 28

20.

Firmware release notes .................................................................................. 28

21.

PCB Conversion - AFTI to or AFG or Tornado or Orbis .................................. 34

22.

Latency ........................................................................................................... 35

23.

Display contrast setting. .................................................................................. 36

24.

AFG & AFTI Analogue Output. ....................................................................... 37

25.

Fault finding. ................................................................................................... 39

26.

Spare parts list ................................................................................................ 41

27.

Assemblies and parts from China ................................................................... 42

28.

Exploded parts diagram .................................................................................. 44

29.

Changes to 300-157-V03 ................................................................................ 46

Содержание AFTI
















































Результаты поиска

Содержание AFTI

Отзывы:

Похожие инструкции для AFTI

Бренды по названию

Популярные бренды

Mecmesin AFTI, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание AFTI

Отзывы:

Похожие инструкции для AFTI

Бренды по названию

Популярные бренды