Matrix SDT 5000 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 67

background image

SDT 5000 User Manual

Document MBUD-0109v11

5.4.2 HIGH SIDE DRIVER OUTPUT

The high side driver output is connected to pin 14 (OUT 2) of J5. The high side driver will pull
the signal to VBAT when active. The high side driver output can source up to 200 mA of current.

High Side Driver

VBAT

Figure 6 - High side driver equivalent circuit

5.4.3 RSSI OUTPUT

The RSSI output is connected to pin 13 (RSSI) of J5. The RSSI output reflects the received signal
strength of the satellite signal. The RSSI output will range from 0 volts to 2.7 volts. A higher
RSSI voltage indicates a stronger received signal. The current RSSI value is available with the
‘

rssi

’ command.

The RSSI is also available on the test port connector as shown in Appendix C.

5.4.4 PWM OUTPUT

The PWM output is connected to pin 16 (PWM) of J5. The PWM signal can generate a
modulated signal with a range of 0 to 3.3 volts with a current of < 100 uA.

This output is currently not implemented in the firmware.

5.5 RTU

Port

The RTU Port is a full RS232 port configured as DTE with the following signals:

Receive is an output connected to pin 16 (RX) on J3.
Transmit is an input connected to pin 17 (TX) on J3.
RS232 Signal ground is connected to pin 18 (GND) on J3.
Request to send is an input connected to pin 19 (RTS) on J3.
Clear to send is an output connected to pin 20 (CTS) on J3.
Data terminal ready is an input connected to pin 21 (DTR) on J3.
Data set ready is an output connected to pin 22 (DSR) on J3.
Carrier detect is an output connected to pin 23 (CD) on J3.
Ring indicator is an output connected to pin 24 (RI) on J3.

Version 1.1, 03/24/06

Page 27

«
...
33
34
35
36
37
...
»

Содержание SDT 5000




































































Отзывы:

Нет отзывов

Похожие инструкции для SDT 5000

Бренд: Sangoma Страницы: 12

Бренд: United Security Products Страницы: 24

Бренд: HTC Страницы: 24

Бренд: Azumi Страницы: 7

Бренд: HTC Страницы: 10

Бренд: Rath Страницы: 9

Бренд: Hammer Страницы: 11

Aastra 480i SIP

Бренд: ADTRAN Страницы: 29

BLACKBERRY P'9982

Бренд: PORSCHE DESIGN Страницы: 226

Бренд: jablotron Страницы: 11

Бренд: Salora Страницы: 33

Бренд: NGM Страницы: 148

Бренд: Samsung Страницы: 144

Бренд: Samsung Страницы: 160

Бренд: Samsung Страницы: 162

Бренд: Samsung Страницы: 186

Бренд: Samsung Страницы: 144

Бренд: Samsung Страницы: 195

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды