Matrix SDT 5000 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 67

background image

SDT 5000 User Manual

Document MBUD-0109v11

3.2.2 COMMON EVENT PARAMETERS

The events are controlled with a number of common parameters including: action, X25
destination address, UDP/IP address and port, acknowledge required flag, maximum number of
buffered alarms, retry timeout, maximum retries, acknowledge required, buffer alarm flag,
connection hold time, and message wait time.

Action

is set to the desired protocol to use to send the message, NONE, X25, X25 fast select, or

UDP. If the action is set to NONE this event is disabled.

X25 destination address

is the address used if the action is set to X25 or X25 fast select.

UDP/IP destination address

is the IP address used if the action is set to UDP. See also UDP/IP

destination port.

UDP/IP destination port

is the UDP port number used if the action is set to UDP.

Acknowledge required flag

is set to TRUE if the alarm must be acknowledged by the host

application before being deleted from the queue.

Maximum number of buffered alarms

specifies how many events can be queued for transmission

before events are dropped. A counter is increment when events are dropped.

Retry timeout

specifies the time between retries of the message when the message transmit fails

or no acknowledge is received. The retry delay is randomly distributed over the minimum retry
time of retry interval, and the maximum retry time of retry timeout * 2 ^retry count.

If

buffer alarm flag

is FALSE

maximum retries

specifies the number of transmission retries

before the alarm is discarded. If the

buffer alarm flag

is TRUE,

maximum retries

specifies the

number of retries for this set of transmission attempts. The alarm will attempt another set of
transmissions when another enabled alarm event occurs or a schedule wakeup event occurs.

Connection hold time

is the time to maintain the connection after the alarm has been sent. A hold

time of zero implies an immediate disconnect after the alarm has been sent.

Message wait time

is the time to keep the transceiver powered on after the hold time expires.

Maximum retries

functionality depends on the buffer alarm flag.

Maximum retries

of zero is no

retries.

3.2.3 PARAMETERS CONFIGURED PER ALARM

The following parameters are configured on a event by event basis:

action, enable, send event

clear flag

and other parameters specific to the event.

Enable flag

is set to TRUE if the event message is to be sent to the host.

Send event clear flag

is set to TRUE if the transition from active to inactive caused a clear event

message to be sent.

Version 1.1, 03/24/06

Page 19

«
...
25
26
27
28
29
...
»

Содержание SDT 5000




































































Отзывы:

Нет отзывов

Похожие инструкции для SDT 5000

Бренд: Yealink Страницы: 8

Бренд: T-Mobile Страницы: 2

Бренд: Audiovox Страницы: 79

Бренд: Aastra Страницы: 2

Бренд: Yealink Страницы: 3

Бренд: Samsung Страницы: 155

Smartphone E-11

Бренд: Etisalat Страницы: 75

Бренд: TCL Страницы: 74

Бренд: EASY3CALL Страницы: 40

Бренд: Avaya Страницы: 237

Бренд: Novatel Страницы: 25

Бренд: Hyundai Страницы: 24

Бренд: Sprint PCS Страницы: 145

Бренд: Dotel Страницы: 37

Бренд: Grandstream Networks Страницы: 62

Telenium IP IP7008D

Бренд: Vodavi Страницы: 2

Бренд: Majestic Страницы: 41

Бренд: Samsung Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды