Matrix SDT 5000 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 67

background image

SDT 5000 User Manual

Document MBUD-0109v11

WARNING - EXPLOSION HAZARD – FUSE MUST ONLY BE CHANGED IN AN AREA
KNOWN TO BE NON-HAZARDOUS. REPLACE FUSE ONLY WITH: 5 AMP, 250 VOLT
FAST BLOW (PART NUMBER: LITTLEFUSE 217005 or 217005XP or F5AL250V).

2.3 Site

Selection

Your SDT 5000 assembly has been thoroughly tested and designed for use in rugged weather
conditions and Class I Division II environments. However, due care and attention is still required for
a proper installation. Select a site with a clear unobstructed line of sight to the satellite. The satellite is
situated over the equator roughly in the center of North America. When possible, select a site with
shelter from extreme weather conditions.

The SDT 5000 is environmentally sealed, so it may be mounted directly outdoors. When
the SDT 5000 is mounted outdoors, it must be mounted with the cable connector
pointing downwards. See

Interface Cable

Mounting

Bracket

Mounting

Pole

Clamps

SDT5000

Antenna

Figure 1.

The unit can also be installed indoors behind a glass window, provided there is a line of sight path
from the antenna to the satellite through the window. When the unit is installed indoors, the unit can
be oriented either vertically or horizontally. Please note that some type of glass may affect the
performance.

Version 1.1, 03/24/06

Page 5

«
...
11
12
13
14
15
...
»

Содержание SDT 5000




































































Отзывы:

Нет отзывов

Похожие инструкции для SDT 5000

Бренд: TANDBERG Страницы: 3

W56P Telesystem

Бренд: Yealink Страницы: 12

Verizon One Talk W60B

Бренд: Yealink Страницы: 8

Бренд: Yealink Страницы: 2

T46S Skype for Business

Бренд: Yealink Страницы: 2

Бренд: Yealink Страницы: 533

Бренд: Planet Страницы: 2

XSTIM Infinity Phone

Бренд: E-MetroTel Страницы: 21

Бренд: HTC Страницы: 226

Бренд: Nortel Страницы: 160

Бренд: Pantech Страницы: 143

Бренд: Sagem Страницы: 97

Бренд: Kogan Страницы: 22

Бренд: Doogee Страницы: 39

BLACKVIEW BV6000

Бренд: Iget Страницы: 52

Бренд: Sagem Страницы: 96

Бренд: Jabbla Страницы: 30

Бренд: TWIG Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды