Matrix SDT 5000 Скачать руководство пользователя страница 3

Страница: 3 / 67

SDT 5000 User Manual

Document MBUD-0109v11

Safety Precautions

Read and understand the entire manual and follow the safety instructions

WARNING!

Replace fuse with same type and rating for protection against fire and damage.

The SDT 5000 is a Radio Frequency (

) generating device. Do not operate the unit

when anyone is in the vicinity noted in the

Safety Information

section of this guide. This

could result in personal injury.

Do NOT operate the SDT 5000 unit in areas where explosives are in use as the

frequency could interfere with the operation, causing hazardous conditions. Do NOT
operate the SDT 5000 unit in areas where two-way radio communications is prohibited

For safety purposes, use caution when determining the SDT 5000 installation location.

CAUTION!

READ THIS MANUAL IN ITS ENTIRETY!

Keep all original Packing Materials.

Follow the instruction enumerated in the

Installation Section

of this guide to ensure

proper hardware installation.

Ensure that the SDT 5000 is installed in a location that will NOT affect the

transmission.

Pay close attention to the electrical power installation requirements described in this guide.

Version 1.1, 03/24/06

Page iii

Содержание SDT 5000




































































Результаты поиска

Содержание SDT 5000

Отзывы:

Похожие инструкции для SDT 5000

Бренды по названию

Популярные бренды

Matrix SDT 5000, Руководство пользователя

Результаты поиска

Содержание SDT 5000

Отзывы:

Похожие инструкции для SDT 5000

Бренды по названию

Популярные бренды