Matrix SDT 5000 Скачать руководство пользователя страница 16

Страница: 16 / 67

SDT 5000 User Manual

Document MBUD-0109v11

System Boot (boot-s v1.0-b1 2006-02-10 16:58:35) ...

CPU RAM Test...Passed

Loading sdt-s v1.0-b1 2006-02-09 16:20:28

0 BSI: Created port COM1

0 BSI: Created port COM2

0 BSI: Created port COM3

0 ID: EEPROM contents validated: 0x3542, 2067 bytes

0 SID: EEPROM contents validated: 0x0005, 16 bytes

0 CAL: EEPROM contents validated: 0x0001, 28 bytes

1 SS: Task MDTN, id 0x3ca450, pri 14, msg 5, tcb 3ca4b4

1 SS: Task MDTX, id 0x3cae98, pri 16, msg 5, tcb 3caefc

1 SS: Task HC12, id 0x3fff30, pri 17, msg 20, tcb 3fff94

1 SS: Task NI-1, id 0x3a89d4, pri 17, msg 40, tcb 3a8a38

2 SS: Task CA-1, id 0x3c9624, pri 18, msg 40, tcb 3c9688

2 SS: Task XIP1, id 0x3b702c, pri 20, msg 40, tcb 3b7090

2 SS: Task LG-1, id 0x3dd11c, pri 21, msg 1000, tcb 3dd180

2 SS: Task MD-1, id 0x3cf33c, pri 25, msg 20, tcb 3cf3a0

2 SS: Task IP-1, id 0x3bd930, pri 28, msg 20, tcb 3bd994

2 IP: Waiting for DSP startup.

2 IP: DSP startup successful.

2 IP: Tuned old freq 0, new freq 1536761000

2 IPLP: Exit low power at: 1995-01-03 23:33:01

2 SS: Task TMM-1, id 0x3d07cc, pri 30, msg 20, tcb 3d0830

2 SS: Task LP-1, id 0x3c652c, pri 35, msg 20, tcb 3c6590

2 SS: Task MP-1, id 0x3c3668, pri 36, msg 20, tcb 3c36cc

2 SS: Task MT-1, id 0x3befb4, pri 36, msg 20, tcb 3bf018

2 SS: Task APt0, id 0x3494d8, pri 38, msg 2, tcb 34953c

2 SS: Task APt1, id 0x347c34, pri 38, msg 2, tcb 347c98

3 SS: Task APt2, id 0x346390, pri 38, msg 2, tcb 3463f4

3 SS: Task COM1, id 0x3d7698, pri 40, msg 30, tcb 3d76fc

3 SS: Task COM2, id 0x3d67d8, pri 40, msg 30, tcb 3d683c

3 SS: Task COM3, id 0x3d5918, pri 40, msg 30, tcb 3d597c

3 SS: Task PS-1, id 0x344b08, pri 42, msg 20, tcb 344b6c

3 SS: Task WA-1, id 0x3afa70, pri 44, msg 20, tcb 3afad4

5 SS: Task AT-1, id 0x33070c, pri 45, msg 20, tcb 330770

5 SS: Task QT-1, id 0x32e834, pri 45, msg 20, tcb 32e898

5 SS: Task AP-1, id 0x34cfb8, pri 55, msg 20, tcb 34d01c

5 AP: Application Ready

5 AP: Protocol mode change to NP.

5 SS: Task ACQ1, id 0x3cb500, pri 80, msg 5, tcb 3cb564

5 SS: Task CAL-1, id 0x3cfb10, pri 118, msg 20, tcb 3cfb74

5 SS: Task NVOL, id 0x3d491c, pri 119, msg 5, tcb 3d4980

8 SS: Task DB-1, id 0x3d16d4, pri 120, msg 20, tcb 3d1738

8 DB: Nonvolatile test...passed

8 SS: Task ID-1, id 0x3d3fb8, pri 122, msg 20, tcb 3d401c

8 SS: Task WD-1, id 0x3d4e58, pri 127, msg 2, tcb 3d4ebc

The SDT 5000 will boot and run a series of self-diagnostic tests. Once the unit has completed the
start up procedures (approximately. 5 seconds) the antenna aiming procedure from section 2.5.1.3
should be followed.

Version 1.1, 03/24/06

Page 8

Содержание SDT 5000




































































Результаты поиска

Содержание SDT 5000

Отзывы:

Похожие инструкции для SDT 5000

Бренды по названию

Популярные бренды

Matrix SDT 5000, Руководство пользователя

Результаты поиска

Содержание SDT 5000

Отзывы:

Похожие инструкции для SDT 5000

Бренды по названию

Популярные бренды