OPERATION
50950436
/
H0521
64
Printed in U.S.A.
All controls must be within easy reach.
The operator must be able to move the
throttle pedal and the control joysticks
through the complete range of motion.
3 .
Fasten the seat belt .
Always fasten the seat belt before oper-
ating the machine. Repair or replace
any damaged seat belt and lock parts
before operation.
4 .
Close the swing-out cab door, if
equipped .
IMPORTANT:
The swing-out cab door
must be closed before the engine can be
started.
5 .
Lower the restraint bar .
IMPORTANT:
The restraint bar must be
lowered before the engine can be started.
6 .
Insert the ignition key into the ignition
switch (G, Fig . 20) and turn the key
clockwise to the first detent. Wait for the
multi-function display to initialize com-
pletely . Indicators on the indicator panel
should light up and a tone will sound .
The battery voltage and preheat indicators
may stay lit for 3-30 seconds .
NOTE:
The preheat indicator may stay
on for longer periods in colder ambient
temperatures.
Fig. 20 -
G
Ignition Switch
NOTE:
When the key is turned clockwise
to the first detent, seat belt indicator acti
-
vates and a tone sounds for 5 seconds as
a reminder to fasten the seat belt.
7 .
When the preheat indicator light goes out,
Turn the ignition key clockwise until the
starter activates . Release the key when the
engine starts .
8 .
If the engine does not start after 15
seconds, turn the ignition key all the
way counter-clockwise, wait 1 minute
and repeat steps 6-8 . If the engine does
not start after several attempts, see
“Connecting/Disconnecting Attachments”
on page 79 .
9 .
Disengage the parking brake .
IMPORTANT:
The lift arm and drive
hydraulics are inactivated if the parking
brake is engaged.
Cold-Starting
If operating in temperatures below 32°F (0°C),
the following are recommended:
• Replace the engine oil with the proper
viscosity oil according to the engine operator’s
manual .
• Make sure the battery is fully charged .
• Install an optional block heater on the engine .
A block heater is recommended for starting
Содержание MUSTANG 1050RT
