Man D2842 LE103 Скачать руководство пользователя страница 67

Страница: 67 / 90

Faults

MAN-Industrial diesel engines D2842 LE103

Carefully read the Operating Instructions before starting any work!
This is especially valid for the chapter on General Safety Instructions
and the safety instructions in each of the chapters.

Fault

Remedy

Possible cause

Engine speed fluctua
tions during operation

inadequate fuel in the tank

Air in fuel system

Tachometer faulty

Injectors faulty

Poor performance

Too much power is demanded from the
engine than it can produce

Air in fuel system

Fuel filter/air filter clogged

Fuel grade does not meet the regu
lations

Insufficient fuel supply

Oil level in oil pan too high

Exhaust pipe clogged

Air intake pipe leaks

Turbocharger leaks or faulty

Insufficient compression in cylinder or
more than 3-4 bar pressure difference
between the cylinders

Rated speed incorrectly set

See "Fluids and Lubricants..."

Fuel feed pump worn or faulty

Check whether the guide tube is
correctly installed and the cor
rect oil dipstick is being used

If coolant or fuel is discovered in
the engine oil, check cylinder
head gasket, cylinder liner gas
ket and piston rings

Coolant temperature
too high, loss of coolant

Coolant level too low

Air in coolant circuit

Radiator very dirty, fins clogged

V-belt for coolant pump not correctly
tightened (slips)

Cap with work valves on expansion
reservoir/radiator is faulty or leaks

Temperature display faulty

Coolant pump leaks, defective (bearing
damage)

Thermostat faulty, does not open

Coolant lines leak, clogged or twisted

Lube-oil pressure too
low

Oil level in oil pan too low

Engine temperature to high

Oil filter clogged

Oil pressure indicator faulty

Selected oil viscosity is inappropriate for
ambient temperature (too thin)

Oil in oil pan is too thin (contains con
densation or fuel)

Bearing heavily worn

Oil pump gears heavily worn

Safety valve in oil circuit faulty (does not
close, spring is worn or broken)

See "Fluids and Lubricants..."

Содержание D2842 LE103



























































































Результаты поиска

Содержание D2842 LE103

Отзывы:

Бренды по названию

Популярные бренды

Man D2842 LE103, Руководство по эксплуатации

Результаты поиска

Содержание D2842 LE103

Отзывы:

Бренды по названию

Популярные бренды