manualshive.com logo in svg

Man D2842 LE103, Руководство по эксплуатации

Поделиться
Скачать
Man D2842 LE103 Скачать руководство пользователя страница 17

General Safety Instructions

MAN-Industrial diesel engines D2842 LE103

17

Carefully read the Operating Instructions before starting any work!
This is especially valid for the chapter on General Safety Instructions 
and the safety instructions in each of the chapters.

2.7

Specific Dangers

The following section describes residual risks which have been identified.

S

Observe the safety instructions listed here and the warnings in the other chapters of these instructions
in order to reduce health hazards and avoid dangerous situations.

Electrical Current

DANGER!

Risk of death caused by electrical current!

There is a risk of death when coming into contact with parts conducting electrical currents. 
Damaged insulation or components can be life threatening.

For this reason:

S

If the insulation is damaged, immediately switch off the power supply and get the insula­
tion repaired.

S

Any work performed on the electrical system may only be made by a qualified electrician.

S

When working on the electrical system the power supply must be switched off and then
properly checked to ensure no electrical current is present.

S

Before starting any maintenance, cleaning or repair work the power supply must be
switched off and secured from being accidentally switched back on.

S

Do not bridge or bypass any fuses. When replacing fuses, ensure to use the correct am­
perage.

S

Keep moisture clear of parts conducting electrical current. This could cause a short-cir­
cuit.

Moving Parts

WARNING!

Risk of injury caused by moving parts!

Rotating or linear moving parts can cause serious injuries.

For this reason:

S

During operation do not reach into or tamper with moving parts.

S

Do not open the covers during operation.

S

Observe the run-on time: before opening any covers ensure that no parts are still moving.

S

Wear close-fitting clothing in the hazard area.

Exhaust gases

WARNING!

Risk of health hazard caused by exhaust gases!

Leaks in the exhaust system can cause dangerous exhaust gases to leak into the engine
room.

For this reason:

S

Ensure sufficient ventilation.

S

Immediately shut down engines with exhaust leaks.

Содержание D2842 LE103



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды