Magnum Energy MMS Series Скачать руководство пользователя | Manualshive

Страница: 48 / 58

background image

© 2017 Sensata Technologies

39

4.0 Maintenance and Troubleshooting

4.1

Recommended Inverter and Battery Care

The MMS Series inverter/charger is designed to provide you with

years of trouble-free service. It is recommended that every 6 months

you perform the following maintenance steps to ensure optimum
performance and to extend the life of your batteries.

WARNING

: Prior to performing these checks, switch off

both the AC and DC circuits.

• Check batteries for cracks, leaks, or swelling – replace as needed.
•

Use baking soda to clean and remove electrolyte spills or buildups.

•

Check and tighten all battery hold-down clamps.

• Clean and tighten (10 to 12 ft-lbs, or 13.6 to 16.3 N m)) all DC

terminals (battery and inverter) and connecting cables.

• Check/

fi

ll battery water levels (liquid lead acid batteries only).

• Check individual battery voltages (replace those that vary more

than 0.3 VDC from each other).

• Check all cable runs for signs of cha

fi

ng – replace as needed.

• Check the inverter’s cooling vents – clean as necessary.

4.2

RV/Marine Off-Season Storage

When placing your coach or boat into seasonal storage, it is
recommended that you perform the following to ensure the system
is properly shut down (or properly con

fi

gured for seasonal storage).

This is especially important for maintaining the batteries.
•  Perform the recommended maintenance steps noted above.
•  Fully charge the batteries.
•  Connect shorepower (if available) and verify that the breaker to

the battery charger is switched ON.

• Verify the inverter is switched OFF.
• Switch off all unnecessary AC and DC loads.

4.3

Resetting the Inverter

Under some fault conditions (i.e., an internal fault), the inverter will
need to be reset. To reset the inverter:
1. Press and hold the Power ON/OFF pushbutton (Figure 1-3, Item

2) for approximately 15 seconds, or until the Status LED (Figure
1-3, Item 1) comes on and

fl

ashes.

2. Release the Power ON/OFF pushbutton once the

fl

ashing has

begun. The Status LED will go off.

3. Press the Power ON/OFF pushbutton again to turn on the inverter.

Info:

The Power ON/OFF pushbutton is a small

momentary

type switch—operated by lightly pressing and releasing.

Maintenance and Troubleshooting

«
...
46
47
48
49
50
...
»

Содержание MMS Series



























































Отзывы:

Нет отзывов

Похожие инструкции для MMS Series

blueplanet 87.0 TL3

Бренд: Kaco Страницы: 200

Бренд: DAAB Страницы: 8

Бренд: Peachtree Audio Страницы: 56

5000W AC Power Inverter

Бренд: Wagan Страницы: 11

Бренд: Lika Страницы: 2

Бренд: Black Box Страницы: 60

Бренд: V2 Страницы: 4

Бренд: Cobra Страницы: 14

Бренд: Advent Страницы: 110

Бренд: ANTAIRA Страницы: 27

Бренд: GME Страницы: 10

Бренд: ADF Web Страницы: 29

Бренд: Lindy Страницы: 12

Бренд: CTC Union Страницы: 2

Бренд: Escient Страницы: 369

Бренд: Z3 Technology Страницы: 76

Profibus AMT58 13x12 PB Series

Бренд: Datalogic Страницы: 97

Бренд: Uniteck Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды