Magnum Energy MMS Series Скачать руководство пользователя | Manualshive

Страница: 12 / 58

background image

© 2017 Sensata Technologies

3

Introduction

All electrical appliances are rated by the amount of power they
consume. The rating is printed on the product’s nameplate label,
usually located on its chassis near the AC power cord. Even though
it is dif

fi

cult to calculate exactly how long an inverter will run a

particular appliance, the best advice is trial and error. Your MMS
Series inverter/charger has a built-in safeguard that automatically
protects your batteries from being over-discharged.

1.5

Standard Features and Benefi ts

The MMS Series inverter/charger

converts 12 volts of direct current

(VDC) power from your battery to 120 volts alternating current (VAC)
power.

The multi-stage battery charger optimizes incoming AC power

using Power Factor Correction (PFC) technology to keep the inverter’s
battery bank fully charged. This inverter is designed to allow easy
installation and use, and with its die-cast aluminum baseplate it
ensures maximum durability and cooler, more ef

fi

cient operation.

The inverter/charger provides the following:
• 1000 watts continuous at 25°C (77°F).
• Numerous protection features to provide a safe and peace-of-

mind operation.

• AC transfer switch circuitry; allowing incoming AC power to

continue to pass-thru to power loads even if the inverter is off.

• Dead battery charging for batteries that are extremely low.
• Automatic 4-stage battery charger with power factor correction

and temperature compensation—for optimum battery charging
(using the temperature sensor).

• Modern and aesthetically pleasing design with a large AC wiring

compartment (provides easy access to AC wiring for simple and
quick connections) and 360° DC connection terminals with color
coded insulating covers.

• True RMS output voltage regulation to ensure the inverter will

deliver the correct amount of power—within the DC input voltage
range and the continuous output power level.

• Quick connection accessory and remote ports—easily accepts

several optional remote controls and the battery temperature
sensor.

«
...
10
11
12
13
14
...
»

Содержание MMS Series



























































Отзывы:

Нет отзывов

Похожие инструкции для MMS Series

Бренд: Ramsey Electronics Страницы: 20

Бренд: Enerdrive Страницы: 24

Бренд: Allen-Bradley Страницы: 4

Бренд: pro user Страницы: 60

COM-K IMR01Z01-E9

Бренд: RKC INSTRUMENT Страницы: 2

Бренд: Solplanet Страницы: 75

Q.HOME+ ESS HYB-G2

Бренд: Q CELLS Страницы: 60

Бренд: 2N Страницы: 17

Бренд: Logicform Страницы: 5

Бренд: Fronius Страницы: 92

Бренд: SIIG Страницы: 34

Бренд: Hall Research Technologies Страницы: 16

Mobile Receiver

Бренд: TracVision Страницы: 76

Бренд: AJA Страницы: 43

5.1 AV Switch Box

Бренд: Jaton Страницы: 16

Cobalt Alpha Series

Бренд: DCCconcepts Страницы: 25

Бренд: Parkside Страницы: 41

Бренд: Escient Страницы: 369

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды