Magnum Energy MMS Series Скачать руководство пользователя | Manualshive

Страница: 45 / 58

background image

© 2017 Sensata Technologies

36

Operation

• Internal

Fault

– The inverter continually monitors several

internal components and the processor communications. If a
condition occurs that doesn’t allow proper internal operation,
the inverter will shut down to protect itself and the connected
loads. The inverter will need to be reset to start operating again.

Table 3-1, Inverter Battery Turn On/Off Levels

3.4 Inverter

Startup

ON/OFF Switch

– The MMS Series can be turned on and off by

lightly pressing and releasing the Power ON/OFF switch on the front
of the inverter. When the inverter is

fi

rst connected to the batteries,

or when its automatic protection circuit has turned the inverter off,
the ON/OFF switch will need to be pressed to start the unit. Once
the inverter has been turned on, pressing the Power ON/OFF switch
alternately turns the inverter on and off.

WARNING:

The Power ON/OFF control switch does not

turn on or off the charger feature. If AC power (utility or
generator) is connected and quali

fi

ed on the AC input,

this AC power will also be available on the AC output and
is not controlled by the Power ON/OFF switch.

Status LED Indicator

– The status indicator is a green LED (Light

Emitting Diode) that provides information on the operational mode of
the inverter. Watch this indicator for at least 10 seconds to determine
the inverter’s operational condition from the information below:

Inverter Mode

Off

– Indicates the inverter is off; there is no AC power from the

inverter, shorepower, or generator at the inverter’s output terminals.

• Blinks On (once every second)

– The inverter is on and is using

energy from the battery. The inverter is either providing full
power to the loads connected to the inverter, or it’s in Search
mode and ready to supply AC power to the connected loads.

Inverter Battery

Turn On/Off

Levels

Inverter Model

MMS1012

MMS1012-G

HBCO

>15.8 VDC

>15.8 VDC

HBCI

15.5 VDC

15.5 VDC

LBCI

≥

12.5 VDC

≥

12.5 VDC

LBCO

(one minute

delay)

10.0 VDC

(9.0 to 12.2 VDC)

10.0 VDC

(9.0 to 12.2 VDC)

LBCO

(immediate)

8.5 VDC

8.5 VDC

«
...
43
44
45
46
47
...
»

Содержание MMS Series



























































Отзывы:

Нет отзывов

Похожие инструкции для MMS Series

Бренд: Yamaha Страницы: 31

Бренд: KROHNE Страницы: 67

PX348 PxArt Audio

Бренд: PXM Страницы: 25

Бренд: OTS Страницы: 3

Бренд: Wacker Neuson Страницы: 22

Бренд: TTI Страницы: 7

Бренд: FireBird Страницы: 44

AS-07UR4SYDDB15

Бренд: Hisense Страницы: 59

Бренд: Vacon Страницы: 44

Бренд: DieHard Страницы: 24

Бренд: B&R Страницы: 45

Бренд: M-system Страницы: 5

Бренд: Briggs & Stratton Страницы: 36

Бренд: Growatt Страницы: 25

Бренд: HEIDENHAIN Страницы: 36

Welbee WB-A350P

Бренд: Daihen Страницы: 150

Бренд: Spatz Страницы: 22

Бренд: GUSTARD Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды