Section 6 - Wiring (continued)
Telemotive TR12 inteleSmart Receiver Instruction Manual – 03/01/07
31
TABLE 2(F) 2-SPEED PROGRAMMING DIAGRAM.
P&H: 2-SPEED, 2-WINDINGS for HOIST;
STANDARD TROLLEY and BRIDGE
HOIST CONNECTIONS
MOTOR 2 CONNECTIONS MOTOR
3 CONNECTIONS
J8-6 HOIST UP (HOT J8-5)
J7-6 TROLLEY DIR 1 (HOT J7-5)
J6-6 BRIDGE DIR 1 (HOT J6-5)
J8-4 HOIST
LOW
SPD (HOT J8-3)
J7-4 TROLLEY
2
ND
SPD (HOT J7-3)
J6-4 BRIDGE
2
ND
SPD (HOT J6-3)
J8-2 HOIST DOWN (HOT J8-1)
J7-2 TROLLEY DIR 2 (HOT J7-1)
J6-2 BRIDGE DIR 2 (HOT J6-1)
J9-6 HOIST HIGH SPD (HOT J9-5)
INDEPENDENT CONNECTIONS
J9-2 AUX 1
(HOT J9-1)
(LATCHABLE Rx S2-2)
J9-4 AUX 2
(HOT J9-3)
(LATCHABLE Rx S2-3)
RECEIVER And TRANSMITTER SWITCH SETTINGS
In the Receiver use the PDA Receiver Programmer to:
o
Set “Receiver access code” and “Frequency”.
o
In the “Receiver Programmer” screen, select under “System” “12 output 2 speed”.
o
In the “Set Status Words” screen, set RX and TX Status Word Switches S1 to S4 as shown below:
X’s are normally OFF (0) but may be turned ON (1) to enable additional features detailed in Section 7-11 Status
Word Programming.
In the transmitter:
•
2-Speed
telePilot
and
telePendant
use the PDA Transmitter Programmer to:
o
Set “Receiver access code” and “Frequency”. (Must be same as receiver).
o
Select under “System” “10K”.
o
Program the configuration switches S3-5, -6 and -7 to OFF (0).
o
Select under “Main/Aux” the word “Aux”.
o
(A 3-Speed
telePendant
can be used as a 2-Speed transmitter. See Section 6-8).
•
MLTX, JLTX and SLTX transmitter switch SW4 “D” program the configuration switches 5, 6 and 7 to OFF (0).
*NOTE: TROLLEY and BRIDGE are listed here as traditional configurations, the installer may choose to define the motors
differently.
Position
Switch
# 1 2 3 4 5 6 7 8
Rx S1
X X X 0 0 X
X
X
Tx S3
X
X X 0
1
0
1 0
Position
Switch # 1 2 3 4 5 6
7 8
Rx S2
0 X X 0 0
0
X
X
Tx S4
0
0 0 0
0
0
0 0
OUTPUTS
J6-6
J6-4
J6-2
BRIDGE*
MOTOR 3
1
ST
2
ND
Dir 1 Dir 2
OUTPUTS
J8-6
J8-4
J8-2
HOIST
1
ST
2
ND
UP DN
2
ND
1
ST
2
ND
1
ST
OUTPUTS
J7-6
J7-4
J7-2
TROLLEY*
MOTOR 2
1
ST
2
ND
Dir 1 Dir 2
2
ND
1
ST
J9-6
INDEPENDENT OUTPUTS
J9-2
AUX 1
J9-4
AUX 2
