Section 7 - Programming (continued)
Telemotive TR12 inteleSmart Receiver Instruction Manual – 03/01/07
46
7-11.9. Tx Status Word S3-1, -2 and -3. (Transmitter
Motion Switch Rearrangement). Normally All OFF.
Definition: Through this feature the conventional
arrangement of transmitter motion switch pairs; Hoist at
the top, Trolley in the middle and Bridge at the bottom,
can be changed without rewiring the receiver.
Programming:
Turn TX Status switch S3 positions 1 through 3 ON or
OFF to obtain the desired configuration. See the Table 7-
2 for the arrangement of programming switches verses
motion switch pairs on the transmitter.
S3-1 S3-2 S3-3 Hoist Trolley Bridge
0 0 0
Pair
1 Pair
2 Pair 3
1 0 0
Pair 1 Pair 3 Pair
2
0 1 0
Pair
2 Pair 3 Pair
1
1 1 0
Pair 2 Pair 1 Pair
3
0 0 1
Pair 3 Pair
1 Pair
2
1 0 1
Pair
3 Pair
2 Pair
1
Table 7-2. Tx Switch S3-1, -2 and -3 Programming,
see diagram below for switch pair location.
7-11.10.
Tx Status Word S3-5 through -8. (Pre-
Configured Select for Custom Cranes Motors).
Normally All OFF.
Definition: Certain types of cranes require custom relay
programming; the most common variations of relay
programming are preprogrammed into the
inteleSmart
receiver and are selectable through Tx Status Switch S3
positions 5 through 8. The available configurations are
shown in Section 6 – Wiring.
Programming:
If a custom crane relay configuration is needed, locate
the appropriate Table in the wiring diagrams in Section 6
– Wiring. Program all receiver switches and transmitter
switches per the instructions under RECEIVER And
TRANSMITTER SWITCH SETTINGS for that table.
7-11.11. Tx Status Word S4-1. (4/5 Motor Aux).
Normally OFF.
Definition: For any receiver configuration greater than 3
motor this switch S4-1 must be turned ON (1). This
switch turned OFF (0) gives only 3 motor
configurations.
Programming:
If a motor configuration greater than 3 motor is needed,
locate the appropriate Table in the wiring diagrams in
Section 6 – Wiring. Program all receiver switches and
transmitter switches per the instructions under
RECEIVER And TRANSMITTER SWITCH SETTINGS
for that table.
Tx Status Word S4-2. (4 Motor, using Select Relays).
Normally OFF. Used with switch S4-1.
Definition: For any receiver configuration using the
Select Relays this switch S4-2 and switch S4-1 must be
both turned ON (1). Turning switch S4-2 on without S4-
1 on is not a valid configuration.
Programming:
If a motor configuration with Select relays is needed
locate the appropriate Table in the wiring diagrams in
Section 6 – Wiring. Program all receiver switches and
transmitter switches per the instructions under
RECEIVER And TRANSMITTER SWITCH SETTINGS.
7-11.12. Tx Status Word S4-3. (Tandem Disable For
Hoist, Trolley or Bridge). Normally OFF.
Definition: Normally for 4 or more operation “Both A
and B” operation is enabled (both MAIN and AUX
motor or Select 2 and Select 1 can be ON at the same
time). Turning ON (1) this feature disables the “Both”
function. (“A” and “B” or Select 1 and Select 2 will not
come on at the same time).
Programming:
Turn the Tx Status Word switch S4 position 3 ON (1) to
prevent both “A” and “B” or Select 1 and Select 2 from
both coming on at the same time. Tandem disable must
also be set in the transmitter also.
Motion Switch
Pair 1
Pair 2
Pair 3
Figure 7-11. Transmitter Switch Pair Location.
