background image

 

Enrange MLTX2 Intrinsically Safe 

Transmitter Instruction Manual 

April 2019 

Page 19 of 44 

 

Figure 6: Normal Operating Screen on Graphic User Interface 

3.7.1 

Watch Dog Indicator (Spinning Arrow) 

The spinning arrow represents the watch dog timer within the CPU of the unit.   
 

NOTE: The arrow should be continuously spinning at all times. If the arrow is not spinning, the transmitter 
will need to be rebooted to operate properly. 

 

3.7.2 

Command Confirmation 

Each time the user operates a control on the transmitter, a message will be displayed on the graphic user 
interface screen confirming what is being operated.   
 
For example, if the second paddle is moved to its 4th position in the UP direction the display will show 
‘MTN2  D1  SP=4’.  This translates to ‘Motion 2, Direction 1, Speed 4’. 
 

3.7.3 

Battery Life Indicator 

Remaining battery life is displayed in the bottom left hand corner of the graphic user interface screen.   
 
Battery life is displayed in 5% increments. 
 

NOTE: If using a different battery pack than what the unit originally shipped with, the battery life indicator 
will be inaccurate unless the dip switch settings are set to the correct battery type being used.  See 
Section 3.1.2 
for details to properly set the dip switches. 
 
NOTE: The battery display is only shown when the battery is powering the device. When the device is 
powered through the optional tethered connection the battery indicator is not displayed and a plug icon is 
display instead. 
 
NOTE: The battery life indictor will only show accurate battery life when using Magnetek approved battery 
packs. 
 
3.7.4 

Signal Strength Indicator 

The Signal Strength Indicator shows the radio signal strength at the receiver. 
 
The Signal Strength Indicator is only available in systems equipped for Two-Way feedback (systems 
utilizing the 433 MHz frequency band do not have Two-Way feedback available). For such systems, 
Signal Strength is displayed at the bottom of the graphic user interface screen.   
 
Signal Strength is displayed in 5% increments. 
 

Содержание Telemotive MLTX2













































Отзывы: