background image

 

S&C ELECTRIC COMPANY

 

 

INSTRUCTION SHEET

 

 663-503

 

Page 1 of 35

August 14, 1995

 

Supersedes Instruction Sheet 663-503 dated 9-20-93          

c

 

1995

s

 

S&C Source-Transfer PMH Pad-Mounted Gear

 

With Micro-AT

 

®

 

   

 

Control

Outdoor Distribution (14.4 kv and 25 kv)

  

 

Section

Page Number

 

INTRODUCTION

Qualified Persons  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2

SAFETY INFORMATION

Understanding Safety-Alert Messages . . . . . . . . . . . . . . . . . . . .  3
Following Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . .  3
Replacement Instructions and Labels  . . . . . . . . . . . . . . . . . . . .  3

SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4
OPERATING DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5
COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6
MINI-RUPTER SWITCHES

Decoupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10
Coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10
Automatic Switch Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .  11
Nonautomatic Switch Operation . . . . . . . . . . . . . . . . . . . . . . . .  11
Charging Operator (Nonelectrical) . . . . . . . . . . . . . . . . . . . . . .  11
Front Barriers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12

FUSING

Assembling the Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15
Installing the Fuse in the Mounting. . . . . . . . . . . . . . . . . . . . . .  15
Warranty Qualifications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15

SWITCHING WITH UNI-RUPTER

Installing and Closing the Fuse . . . . . . . . . . . . . . . . . . . . . . . . .  16
A Note on Single-Pole Switching . . . . . . . . . . . . . . . . . . . . . . . .  20
Opening and Removing the Fuse. . . . . . . . . . . . . . . . . . . . . . . .  20

 

INSTRUCTIONS

 

For Operation

 

Section

Page Number

 

RE-FUSING

How to Detect and Replace a Blown Fuse . . . . . . . . . . . . . . . .  23
Installing the Fuse in the Mounting. . . . . . . . . . . . . . . . . . . . . .  24

FINAL CHECKS BEFORE WALKING AWAY. . . . . . . . . . . . . . . .  25
IF OPERATOR STALLS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26
MAINTENANCE

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  27
Returning Equipment to Service . . . . . . . . . . . . . . . . . . . . . . . .  28
Enclosure Finish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  28

APPENDIX A

Preliminary Tryout Before Gear Is Energized—Optional  . . .  29

APPENDIX B

Dielectric Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  29

APPENDIX C

Ratings for S&C Mini-Rupter Switches. . . . . . . . . . . . . . . . . . .  29
Ratings for S&C Power Fuses with Uni-Rupter. . . . . . . . . . . .  30

APPENDIX D

Optional Features  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31
Accessories  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33

APPENDIX E

Current-Limiting Fuses for Use in

S&C PMH Pad-Mounted Gear  . . . . . . . . . . . . . . . . . . . . . . . . .  34

 

TABLE OF CONTENTS 

 

This publication contains instructions for operation of fuses and Mini-Rupter

 

®

 

  Switches in S&C

Source-Transfer PMH Pad-Mounted Gear. For instructions regarding field programming and
operation of the S&C Micro-AT Source-Transfer Control, refer to S&C Instruction Sheet 515-500.
For operating instructions regarding the optional test-panel feature (Catalog Number Suffix “-Y5”),
if furnished, refer to S&C Instruction Sheet 515-505.

Summary of Contents for PMH




































Reviews: