M/A-Com Orion Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 80

background image

MOBILE DATA

The

Orion

radios when operating in the EDACS configuration permit either

voice or data calls to be transmitted or received. The radio can handle only
one type of call at a time; however, selection of either data or voice is
selected transparently by the operator through normal usage of the radio. Data
communications is not supported in the conventional mode.

The mobile radios may be connected to Mobile Data Terminals (MDT) or to a
host computer. Any RS-232 compatible device that supports the Radio Data
Interface (RDI) protocol (Version 1.91 or greater) may be connected to the
mobile radio. Support for MDT's or host computers is a programmable option
per radio. Additionally, radios programmed for host computers may also be
programmed for data only operation (no voice calls transmitted or received).

NOTE

Turn the power of the radio OFF before connecting or
disconnecting any cables, including the data cable.
Also, turn the power of the radio OFF when docking or
undocking a connected laptop computer. Failure to turn
the power of the radio OFF may damage the radio,
requiring the replacement of an internal non-user
serviceable fuse.

Displays

The following will be displayed on the control unit during the various states of
data mode of operation.

TX DATA

Displayed on bottom line of display when the radio is
transmitting a data call.

RX DATA

Displayed on bottom line of display when the radio is
receiving a data call.

DATA OFF

Displayed on top line of display when the radio is in the data
disabled state.

DATA ON

Displayed for two seconds on top line of display when the
radio is toggled to the data enabled state.

Data OFF Operation

The radio can be placed in the data disable state by any of the following
methods. When the data state is disabled, the control unit displays "DATA
OFF" on the top line. An ongoing data call is allowed to complete except in
the case of declaring an emergency.

•

Removing the microphone from the hook switch (hook switch option
must be enabled by pre-programming).

46

«
...
44
45
46
47
48
...
»

Содержание Orion

















































































Отзывы:

Нет отзывов

Похожие инструкции для Orion

Бренд: Kruger&Matz Страницы: 44

Бренд: CARLO GAVAZZI Страницы: 32

Бренд: GPX Страницы: 2

Бренд: Radio Shack Страницы: 16

WEATHER TRACKER FR800

Бренд: Eton Страницы: 40

Бренд: Albrecht Страницы: 23

ElectroMate VEC095

Бренд: Vector Страницы: 20

Бренд: Mockett Страницы: 2

Бренд: Sencor Страницы: 10

Бренд: Briggs & Stratton Страницы: 156

Бренд: Sonos Страницы: 18

Бренд: Banner Страницы: 2

Бренд: Briggs & Stratton Страницы: 7

Бренд: Generac Power Systems Страницы: 80

Бренд: Majorcom: Страницы: 20

Бренд: IPMobileNet Страницы: 41

Бренд: QFX Страницы: 6

Бренд: Curtis Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды