LuxHome LHK100SU Скачать руководство пользователя страница 7

7

Remote Control Unit

The  Remote  Control  Unit  is  used  to  Arm  and Disarm the system.

The  Remote  will  activate  the  Instant-Arm,  Delay-

Arm or Disarm functions.

The  Remote  Control  also  incorporates  a  Personal 

Attack  Switch  (PAS).  Activating  the  PAS  will 

immediately initiate a Full Alarm condition whether 

the  system  is  Armed  or  Disarmed,  (unless  the 

system is in Service, Test or Program mode).

Any number of Remote Controls can be used with 

your system, providing they are all coded with the 

same system House Code.

The Remote Control is powered by a CR03 type Lithium Cell battery which under normal conditions 

will have a typical life in excess of 1 year. Under normal battery conditions the LED on the Remote 

Control will only illuminate when a button is pressed. However, under low battery conditions the LED 

will flash every time the button is pressed. When this occurs the battery should be replaced as soon 

as possible.

Setting the Remote Control

1.  Remove  the  front  cover  by  undoing  the  small screw on the rear of the Remote Control.

.  Located above the battery is a row of  8  DIP switches. 

Select and record a random combination of ‘ON’ and 

‘OFF’ positions for the DIP switches. This will be the 

system House Code and must be set to the same ON/

OFF combination as the House Code DIP switches in 

all other System Devices.

Important:

 The House Code for your system should 

be changed from the factory default setting.

3.  To  utilise  the  panic  facility  on  the  Remote  Control, 

remove  the  Jumper  Link.  If  ‘panic’  is  not  required 

leave the Jumper Link in place.

4.  Remove the battery from its packaging and insert it under the clip ensuring that the +v terminal 

faces upwards away from the PCB.

5.  Replace the front cover and fixing screw.

Testing the Remote Control

1.  Press  the 

  button.  The  Transmit  LED  should  illuminate  while  the  button  is  pressed  and 

extinguish within 1 second of releasing the button.

.  Press the 

 and 

 buttons in turn to ensure that the Transmit LED illuminates as before.

Transmit  LED 

Arm

 

Delay-Arm

 

Slide up 

to operate

 

Disarm

 

 

Personal Attack

 

House Code 

Dip Switches

 

Jumper Link

 

Battery Clip

 

 

Battery

 

Содержание LHK100SU






























Отзывы: