LuxHome LHK100SU Скачать руководство пользователя страница 15

15

External Solar Siren

Siren Housing

The  Siren,  Strobe  Light  and  Solar  Panel  are  all  encapsulated 

within  a  tough  polycarbonate  housing.  This  housing  provides 

full  protection  against  adverse  weather  conditions. All  electronic 

components are specially treated to ensure long, reliable, trouble 

free  operation  and  an  integral  tamper  switch  gives  maximum 

security protection to the unit.

An  LED  indicator  unit  is  built  into  the  Siren  to  act  as  a  visible 

deterrent  and  indication  that  the  system  is  active.  The  LEDs 

will  slowly  and  alternately  flash  whether  the  system  is  Armed 

or  Disarmed.  When  an  alarm  occurs  the  LEDs  will  flash  rapidly 

together.

An  integral  tamper  switch  provides  additional  security  protection 

to  the  Siren  and  will  immediately  trigger  an  alarm  should  any 

unauthorised  attempt  be  made  to  interfere  with  and  remove  the 

Siren cover, (unless the Siren is in Service Mode).

Rechargeable Battery

The Solar Siren is powered by a high capacity battery. A Solar Panel mounted on the top of the 

housing charges the battery during daylight hours. During darkness, only a small amount of energy 

is required to maintain the Solar Siren unit.

Initial Power-Up Battery

An Alkaline 9V PP3 battery is supplied in the Siren & Strobe unit to provide the initial power to the 

system.

Siren Code

An encrypted code is set using a combination of miniature DIP switches. This enables you to select 

a unique security code for your installation.

Choosing a Location for the Solar Siren

The Siren & Strobe unit should be fitted to the outside 

of the building in a position that is clearly visible and at 

a height which is relatively inaccessible to an intruder.

Although the Siren & Strobe is designed to work on any 

aspect wall, you should refrain from fixing the unit on a 

North facing wall where possible.

Shadows  cast  by  neighbouring  walls,  trees  and  roof 

overhangs  should  also  be  avoided.  In  practice,  the 

Siren  &  Strobe  should  be  positioned  a  minimum  of 

twice  the  width  of  the  eaves  overhang,  below  the 

eaves.  Remember  that  in  winter  the  sun  is  lower  in 

the sky and you should avoid winter shadows where 

possible.

Содержание LHK100SU






























Отзывы: