Learning to Perform
Basic Operations
60
Operating the inverter in AUTO Mode
1
In OFF mode (when the OFF LED is on), move to Parameter mode and configure the
command source at DRV-07 (frequecy reference source).
2
Press the [AUTO] key to enter AUTO mode. In AUTO mode, the inverter operates
based on the input from the command source set at DRV-07. For example, if DRV-07
(frequency reference
source) is set to ‗0 (Keypad)‘, the frequency reference is set, and
the run command is set to
‗ON‘, the inverter starts operating as soon as the [AUTO] key
on the keypad is pressed.
3
Press the [Auto] key again to stop the inverter operation using the keypad. In AUTO
mode, the inverter begins or stops operating when the [AUTO] key is pressed.
Note
•
You can stop the inverter operation by pressing the [OFF] key when the command source is
set to ‗Keypad.‘ In this case, however, the inverter enters OFF mode from AUTO mode.
•
If the network communication is set as the command source, the inverter is operable only in
AUTO mode. For example, if the run command is set to ‗ON‘ via the network
communication and the inverter is in OFF mode, the [AUTO] key must be pressed to start
the inverter operation.
•
The inverter is operable only in HAND and AUTO modes, but the Fire mode functions
operate even when the inverter is in OFF mode.
Содержание H100
