LS SV-xxx-iP5A-2, Руководство пользователя

Страница: 131 / 138

Appendix C
– Related parameters
ix
APPENDIX C- RELATED PARAMETERS
Use Related parameter codes
Adjusting Accel/Decel time and
pattern DRV-01 [Acceleration Time], DRV-02 [Deceleration Time],
FU1-02 [Acceleration Pattern], FU1-03 [Deceleration Pattern]
Reverse rotation prevention FU1-01 [Run Prevention (Forward/Reverse Prevention)]
Accel/Decel at continuous rating
range FU1-02 [Acceleration Pattern],
FU1-03 [Deceleration Pattern]
Adjusting braking operation
FU1-20 [Start Mode], FU1-21~22 [DC Injection Braking Time
and Value at Starting], FU1-23 [Stop Mode], FU1-24~27 [DC
Injection Braking On-delay Time, Frequency, Time and Value]
Operations at freq. over 60 Hz
FU1-30 [Max. Frequency], FU1-35 [High Limit Frequency],
I/O-05 [V1 Input Maximum Voltage], I/O-10 [Frequency
Corresponding to I Input Max. Current], I/O-16 [Frequency
Corresponding to Pulse Input Max. Freq.]
Selecting an appropriate output
characteristics for the load FU1-30 [Max. Frequency],
FU1-31 [Basic Frequency]
Adjusting motor output torque
FU1-32 [Starting Frequency], FU1-71[Stall Prevention Level],
FU2-67~69 [Torque Boost], FU2-40 [Motor Capacity Selection]
Output frequency limit
FU1-33~35[Frequency Limit selection, Hihg/Low Limit Freq.],
I/O-01~16 [Analog Frequency Setting]
Motor overheat protection
FU1-60~62 [Electronic Thermal Selection and Level], FU2-40
[Motor Capacity Selection], I/O-97, 98 [Overheat trip selection
and Motor overtheat trip temperature]
Multi-step operation
I/O-20~27 [Programmable Digital Input Terminal Define],
DRV-00 [Command Frequency], 05~07,I/O-31~42 [Multi-step
Frequency], FU1-34~35 [Hihg/Low Limit Freq.]
Jog operation I/O-30 [Jog Frequency Setting]
Frequency jump operation
FU2-10 [Frequency Jump Selection] ,
FU2-11~16 [Jump Frequency High/Low Limit]
Electronic brake operation
Timing I/O-74,75 [Frequency Detection Level and Bandwidth],
I/O-76~79 [Programmable Digital Output Terminal Define]
Display of rotating speed etc.
DRV-09 [Motor Speed (Rpm)],
FU2-47 [Gain for Motor Speed Display]
Function change prevention FU2-94 [Parameter Lock]
Energy saving FU1-51~52 [Energy Save]
Auto-restart operation after
alarm stop FU2-20 [Power ON Start Selection],
FU2-21 [Restart after Fault Reset]
2
nd
motor operation APP-20~29 [2
nd
Function]
PID feedback operation APP-02~25 [PID Operation]
Adjusting frequency reference
and output
I/O-01~16 [Analog Frequency Setting]
Switchover operation between
Commercial Line and Inverter I/O-20~27 [Programmable Digital Input Terminal Define],
I/O-76~79 [Programmable Digital Output Terminal Define]
Frequency Meter Calibration I/O-70~73 [S0/S1 Analog Output]
Operation via Communication
with a PC
I/O-90 [Inverter Number], I/O-91 [Baud Rate Selection],
I/O-92 [Operation method at loss of freq. reference],
I/O-93 [Wating time after loss of freq. reference]