Logic DLC NET Series Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 78

Logic DLC NET Series Скачать руководство пользователя страница 9

USE AND MAINTENANCE MANUAL

– DLC

NET

Series

General information

LOGIC S.r.l. - M0145Db.docx

Mod. L0006A01 of 30/05/2016

Page 9 of 78

2 General information

2.1 Introduction

This  manual  includes  instructions  for  use  and  maintenance  of  the  instrument.  Its
content  is  directed  to  operators  previously  instructed  on  the  precautions  to  be
taken.

For  a  correct  use  of  the  instrument  in  question,  read  and  follow  the  instructions
contained in this manual. Our technical support is always available to provide any
clarifications  that  were  necessary  to  your  staff  responsible  of  commissioning  of
equipment LOGIC S.r.l..

The microprocessor conditioners for load cells series DLC

NET

are designed to meet

the needs required by the weighing systems.
An easy installation together to a simple operating mode, allow to this tool an
immediate and correct use.

The reliability and accuracy characteristics allow its use in harsh environmental
conditions and therefore suitable for use in an industrial environment.

2.2 Use and conservation of the manual

The purpose of this manual is to provide the directions to use the instrument safely
and perform the installation procedures and routine maintenance. Any calibration,
adjustment and extraordinary maintenance operations are not covered in this text,
being the exclusive competence of the technical assistance, which must assist on
the instrument in accordance with the technical specifications and project for which
it was manufactured.

The  reading  of  this  manual  is  essential,  but  it  cannot  replace  the  competence  of
the technical personnel who must have obtain a preliminary training.

The  manual  must  be  kept  intact  and  in  good  condition  throughout  the  life  of  the
instrument.  After  use,  store  in  a  safe  and  secure  place,  together  with  the  CE
certification.

If  the  documentation  is  lost  or  damaged  you  can  obtain  a  copy  from  the
manufacturer, mention the order number and the serial number of the instrument.

The  instruments  of  DLC

NET

series are made in accordance with the applicable

directives in the European Community and the technical standards that include
their requirements, as certified by the Declaration of Conformity issued by the
manufacturer and attached to the manual.

«
...
7
8
9
10
11
...
»

Содержание DLC NET Series















































































Отзывы:

Нет отзывов