Lithonia Lighting RSX1 LED P4 Скачать руководство пользователя

Страница: 8 / 16

Installation Instructions
RSX LED

RSX MAST ARM ADAPTOR INSTALLATION

8. Reorient luminaire to desired position on the tenon

(See Figure 11a & 11b).

9. Insert provided 7/16"-14 x 4-1/2" bolt through

Mast Arm Mount and drilled 1/2" Ø hole on tenon

and place provided 7/16" nut onto bolt and tighten

securely to 45-50 ft-lbs.

10. Evenly tighten the Six (6) 3/8-16 UNC

Mast Arm Set Bolts while maintaining the correct

position of the luminaire to 23-27 ft-lbs.

11. Energize the luminaire to verify its operation

and proper illumination of area.

WARNING: USE AND PROPERLY TIGHTEN

THRU-BOLT AND NUT. FAILURE TO CORRECT-

LY INSTALL COULD RESULT IN SERIOUS INJURY

OR DEATH.

7/16-14 Bolt

Set Bolts

Pole Tenon

Thru Bolt

Hole

Figure 11a

Figure 11b

Lithonia Lighting Outdoor

One Lithonia Way, Conyers, GA 30012

Phone: 800-279-8041 Fax: 770-918-1209

www.lithonia.com

Part Number: IN-379 Rev F

Revision Date: 11/19/18

Содержание RSX1 LED P4

















Результаты поиска

Содержание RSX1 LED P4

Отзывы:

Похожие инструкции для RSX1 LED P4

Бренды по названию

Популярные бренды

Lithonia Lighting RSX1 LED P4, Руководство пользователя

Результаты поиска

Содержание RSX1 LED P4

Отзывы:

Похожие инструкции для RSX1 LED P4

Бренды по названию

Популярные бренды