Lithonia Lighting RSX1 LED P4 Скачать руководство пользователя

Страница: 12 / 16

Installation Instructions
RSX LED

5. Loose the two (2) 8-32 splice access cover fasten-

ers from knuckle assembly, remove the splice access

cover, and pull supply wire leads from knuckle cavity.

6. Remove tilt limiting screw if necessary (See Fig-

ure 13c, 13d). Note: Luminaire can be tilted up to 90

degrees (maximum) above horizontal.

7. Make all wiring connections via the supplied wire

leads in accordance with NEC and local codes.

8. Push all fixture and supply wires completely within

the knuckle cavity. Ensure the splice box gasket is in

place and replace the splice access cover. Tighten the

two captive screws with the 9/64 Allen wrench to 18-

20 in-lbs (overtighten can cause thread stripping and

void all warranties) (See Figure 13c & 13d).

9. Aim fixture as required and tighten the 7/16-14

SHC knuckle adjustment bolt using an approximately

38 ft-lbs. (See Figure 13e)

10. For units with photocontrol receptacle, the fixture

mounting/aiming angle must be restricted to ± 45°

from horizontal per ANSI C136.10-2010.

11. Energize the luminaire to verify its operation and

proper illumination of area.

WARNING: DO NOT MOUNT THE KNUCKLE FIT-

TER TO A TENON BELOW HORIZONTAL EVEN

WITH PROPERLY TIGHTEN THRU-BOLT AND

LOCKNUT. FAILURE TO CORRECTLY INSTALL

COULD RESULT IN SERIOUS INJURY OR DEATH.

Cover

Gasket

Remove Tilt

limiting screw

Figure 13d

Figure 13e

Figure 13c

Splice

access

cover fasteners

Tilt

limiting screw

Knuckle adjustment Bolt

Lithonia Lighting Outdoor

One Lithonia Way, Conyers, GA 30012

Phone: 800-279-8041 Fax: 770-918-1209

www.lithonia.com

Part Number: IN-379 Rev F

Revision Date: 11/19/18

Содержание RSX1 LED P4

















Результаты поиска

Содержание RSX1 LED P4

Отзывы:

Похожие инструкции для RSX1 LED P4

Бренды по названию

Популярные бренды

Lithonia Lighting RSX1 LED P4, Руководство пользователя

Результаты поиска

Содержание RSX1 LED P4

Отзывы:

Похожие инструкции для RSX1 LED P4

Бренды по названию

Популярные бренды