Lithonia Lighting RSX1 LED P4 Скачать руководство пользователя страница 4

Страница: 4 / 16

Lithonia Lighting Outdoor

One Lithonia Way, Conyers, GA 30012

Phone: 800-279-8041 Fax: 770-918-1209

www.lithonia.com

Part Number: IN-379 Rev F

Revision Date: 11/19/18

Installation Instructions
RSX LED

4. The luminaire is supplied with a variety of slots to

align with existing pole mounting drill patterns. The top

hole of the luminaire arm has a key hole slot.

Place the luminaire onto the top bolt by passing the head

through the key slot and resting the luminaire down securely

in place (See Figure 3).

WARNING: THE LUMINAIRE IS NOT COMPLETELY

LOCKED DOWN YET. SPECIAL CARE MUST BE TAKEN

TO AVOID JARRING THE LUMINAIRE FROM ITS REST-

ING POINT, OTHERWISE THE LUMINAIRE COULD

FALL AND CAUSE SERIOUS INJURY OR DEATH!

Ensure the luminaire is resting securely on the top bolt. Snug

the bolt but do not completely tighten. Thread the second

bolt through the arm slot and into the available threaded hole

of the mounting bar (See Figure 4).

5. The luminaire is supplied with a clearance slot in the

back to allow wires to be pulled into the pole on existing hole

patterns. Insert the wires through the clearance slot shown in

Figure 5 and pull them into the pole.

6. Ensure luminaire is straight/level making sure that no wires

are pinched, tighten the two bolts with a 3/8 socket to 20-30

ft-lbs (overtightening can damage components and void war-

ranties). Make sure that wires are not pinched and tuck excess

wire up into the luminaire mounting area.

7. Reinstall the SPA Cover that was removed, tighten the two

captive screws with the 9/64 Allen wrench to 18-20 in-lbs

(overtighten can cause thread stripping and void all warran-

ties)(See Figure 6).

8. Make wire connections in the pole, observing proper volt-

age and polarity. Connect green ground wire from the fixture

to the field ground wire. Secure wires; push back into pole

and replace pole cap.

First Bolt

Key

Hole Slot

location

Figure 3

Figure 4

Figure 5

Figure 6

Second Bolt

SPA Cover

Mounting

Bolts

Содержание RSX1 LED P4

















Результаты поиска

Содержание RSX1 LED P4

Отзывы:

Бренды по названию

Популярные бренды

Lithonia Lighting RSX1 LED P4, Руководство пользователя

Результаты поиска

Содержание RSX1 LED P4

Отзывы:

Бренды по названию

Популярные бренды